系統下,地球坐標轉換的源代碼,在WGS-84坐標和北京54坐標之間的一套轉換參數,可以全國通用的，在每個地方會不一樣，因?yàn)樗鼈兪莾蓚€不同的橢球基準。 // WGS2GK.CPP : C++ version of Ottmar Labonde s WGSDHDN3.PAS with CPU time measurement // compile with MS Visual C++ version 6.0 or do the necessary modifications for your compiler // // Conversion of
TOYFDTD1 is a stripped-down minimalist, 3D FDTD code demonstrating the basic tasks in implementing a simple 3D FDTD simulation. An idealized rectangular waveguide is modeled by treating the interior of the mesh as free space and enforcing PEC conditions on the faces of the mesh. A simplified plane wave source is inserted at one end. First released 12 April 1999. Version 1.03 released 2 December 1999.
c語言編譯器，跨平臺，4.2版本
lcc version 3.x is described in the book "A Retargetable C Compiler:
Design and Implementation" (Addison-Wesley, 1995, ISBN 0-8053-1670-1).
There are significant differences between 3.x and 4.x, most notably in
the intermediate code. For details, see
http://www.research.microsoft.com/~drh/pubs/interface4.pdf.
c語言編譯器，3.6版本
lcc version 3.x is described in the book "A Retargetable C Compiler:
Design and Implementation" (Addison-Wesley, 1995, ISBN 0-8053-1670-1).
There are significant differences between 3.x and 4.x, most notably in
the intermediate code. For details, see
http://www.research.microsoft.com/~drh/pubs/interface4.pdf.
mp3設計程序資料，采用c語言編寫。
README file for
yampp-3 source code 2001-05-27
This is the current state of the yampp-3 source code, 2001-05-27.
This code is intended to run on Rev. B of the yampp-3 PCB, but can
ofcourse be used on compatible systems as well.
It still uses the "old" song selection system as the yampp-2.
However, the disk handling routines has improved a lot and the
obviosly, the new VS1001 handling has been put in.
The codesize is almost at it s maximum at 1F40 bytes.
A .ROM file is included if you don t have the compiler set up.
For now, the documentation is in the code
The project KEIL_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the Keil ARM toolchain.
The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module.
The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
UART I/O and Memory Allocation Example for GNU
The project GNU_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the GNU toolchain.
The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module.
The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
用CY7C63723設計的鼠標固件程序
chip.c - include file that defines CY7C63723 constants
- combi.c - main source file
- combi.hex - Intel hex file for programming a CY7C63723 microcontroller
- combi.lst - output listing from c-compiler for use with the CYDB debugger
- macros.h - defines macros used in combi.c
- ps2defs.h - defines PS/2 interface constants
- usb_desc.h - defines the USB descriptors
- usbdefs.h - defines USB interface constants
uc/os-ii for 8051
This package provides the sources required to use the uC/OS-II v2.00
real time kernel on the 8051 processor. To use this package you will
need the TASKING C Compiler toolset v6.0r1 or higher.
For info on TASKING products you can contact our Web-site at:
http://www.tasking.com
Unzip the zipfile in the root of the drive where you also installed
the uC/OS-II general sources. The following directories will be
added:
\SOFTWARE\UCOS-II\8051
This directory contains the microprocessor specific source code
\SOFTWARE\UCOS-II\ex1_8051r
This directory contains the project files for the first example
\SOFTWARE\UCOS-II\ex2_8051r
This directory contains the project files for the second example
