Although some FX1-based devices may use the FX1鈥檚 CPU to process USB data directly (Port I/O Mode), most applica- tions use the FX1 simply as a conduit between the USB and external data-processing logic (e.g., an ASIC or DSP, or the IDE Controller on a hard disk drive).
標簽： Although directly devices process
上傳時間： 2014-01-08
上傳用戶：2467478207
This application note describes how to connect Ethernet interface with NXP LPC2000 series ARM MCU. Reference schematics and Ethernet driver source code is attached, with RTL8019AS as Ethernet Controller. The document also shows how to configure uClinux Ethernet options in LPC22xx development system
標簽： application describes interface Ethernet
上傳時間： 2017-04-09
上傳用戶：lingzhichao
VMEbus slave architecture source code Can be implemented on the slave board of a chasis as slave Controller
標簽： slave architecture implemented VMEbus
上傳時間： 2017-04-12
上傳用戶：遠遠ssad
The paper describes the concept and realization of the DOOCS control software for FPGAbased TESLA cavity Controller and simulator (SIMCON). It bases on universal software components, created for laboratory purposes and used in MATLAB based control environment. These modules have been recently adapted to the DOOCS environment to ensure a unified software to hardware communication model. The presented solution can be also used as a general platform for control algorithms development. The proposed interfaces between MATLAB and DOOCS modules allow to check the developed algorithm in the operation environment before implementation in the FPGA. As the examples two systems have been presented.
標簽： realization FPGAbased describes the
上傳時間： 2017-04-16
上傳用戶：koulian
Servomotors are available as AC or DC motors. Early servomotors were generally DC motors because the only type of control for large currents was through SCRs for many years. As transistors became capable of controlling larger currents and switching the large currents at higher frequencies, the AC servomotor became used more often. Early servomotors were specifically designed for servo amplifiers. Today a class of motors is designed for applica-tions that may use a servo amplifier or a variable-frequency Controller, which means that a motor may be used in a servo system in one application, and used in a variable-frequency drive in another application. Some companies also call any closed-loop system that does not use a stepper motor a servo system, so it is possible for a simple AC induction motor that is connected to a velocity Controller to be called a servomotor.
標簽： motors Servomotors servomotors available
上傳時間： 2014-08-10
上傳用戶：源碼3
Evaluation of designing a cheap Ethernet based Florescent Light Dimmer vs. using the next generation DALI ballast and Controller
標簽： Evaluation Florescent generation designing
上傳時間： 2017-05-11
上傳用戶：宋桃子
這個設計是使用Virtex-4實現DDR的控制器的，設計分為三個主要模塊：Front-End FIFOs,DDR SDRAM Controller和Datapath Module。其中主要是DDR SDRAM Controller,當然還有測試模塊。
上傳時間： 2017-05-20
上傳用戶：llandlu
This manual describes SAMSUNG s S3C2410A 16/32-bit RISC microprocessor. This product is designed to provide hand-held devices and general applications with cost-effective, low-power, and high-performance micro-Controller solution in small die size. To reduce total system cost, the S3C2410A includes the following components separate 16KB Instruction and 16KB Data Cache, MMU to handle virtual memory management, LCD Controller (STN & TFT), NAND Flash Boot Loader, System Manager (chip select logic and SDRAM Controller), 3-ch UART, 4-ch DMA, 4-ch Timers with PWM, I/O Ports, RTC, 8-ch 10-bit ADC and Touch Screen Interface, IIC-BUS Interface, IIS-BUS Interface, USB Host, USB Device, SD Host & Multi-Media Card Interface, 2-ch SPI and PLL for clock generation.
標簽： This microprocessor describes S3C2410A
上傳時間： 2013-11-30
上傳用戶：GavinNeko
This is example of using Atmel at89c5131 MCU with at49db11(spi dataflash) and epson s1d1335 graphic Controller.
標簽： dataflash example graphic s1d1335
上傳時間： 2017-06-18
上傳用戶：GHF
Web based binary image upload for ARM LPC2366 Controller. Toolchain is Keil Realview MDK ARM ver 3.2 with RL ARM Real time Lib 3.40. RAR file contains webiap2.cgi file and HTTP_cgi file. HTTP_cgi file is modified in cgi_process_data to upload binary image of application using HTTP protcol. File upload is using HTML syntax method=\"post\" ENCTYPE=\"multipart/form-data\
標簽： web_based
上傳時間： 2013-12-17
上傳用戶：ukuk
蟲蟲下載站版權所有 京ICP備2021023401號-1
