fast calculation of image moments based on Fluss and Tuk s method Described in "On the Calculation of Moments"
標簽： calculation Described Calculat moments
上傳時間： 2013-12-24
上傳用戶：515414293
fuzzy systems for wind has been Described in this controller run using matlab
標簽： controller Described systems matlab
上傳時間： 2017-07-05
上傳用戶：亞亞娟娟123
Feeding antennas with proper signals can be difficult. The signal is often Described as a voltage, and voltages are not well defined in electromagnetic wave formulations. There are several tricks to model voltage generators in such situations, and one is the magnetic frill. This model shows the basic steps of defining a magnetic frill voltage generator for a dipole antenna, and it also compares the resulting antenna impedance with known results.
標簽： difficult Described antennas Feeding
上傳時間： 2013-12-25
上傳用戶：yulg
Feeding antennas with proper signals can be difficult. The signal is often Described as a voltage, and voltages are not well defined in electromagnetic wave formulations. There are several tricks to model voltage generators in such situations, and one is the magnetic frill. This model shows the basic steps of defining a magnetic frill voltage generator for a dipole antenna, and it also compares the resulting antenna impedance with known results.
標簽： difficult Described antennas Feeding
上傳時間： 2013-12-21
上傳用戶：GavinNeko
Fp Growth sample, found on other sites with the main part Described.
標簽： Described Growth sample found
上傳時間： 2013-12-15
上傳用戶：xlcky
本書闡述了用vc++來開發usb接口的程序。開發環境：vc6.0，格式：pdf-The book Described by vc++ To develop procedures for usb int
標簽： writeUSBprogram VC
上傳時間： 2013-07-26
上傳用戶：asdfasdfd
This note describes some of the unique IC design techniques incorporated into a fast, monolithic power buffer, the LT1010. Also, some application ideas are Described such as capacitive load driving, boosting fast op amp output current and power supply circuits.
上傳時間： 2013-11-12
上傳用戶：671145514
針對科研實驗中對拉壓千斤頂加載過程控制的需要，采用ATmega128單片機控制步進電機進而實現對執行系統的電動泵站實行自動控制。對力和位移的數據采集與處理及用步進電機控制電動泵站手柄的技術細節作了重點描述。通過單片機的A/D變換器對AMP放大模塊采集的電橋信號作量化處理，千斤頂的操控手柄位置依電動油泵閥門開啟的方向和大小作若干定位，單片機根據力或位移傳感器信號，實時控制步進電機驅動手柄旋轉到相應操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were Described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
上傳時間： 2014-01-16
上傳用戶：hasan2015
詳細介紹工控軟件組態王與單片機多機串口通訊的設計原理。分析組態王提供的直接與單片機串口通信方法的優點，給出系統基于RS-485總線傳輸的接口電路原理圖。根據組態王提供的通訊協議和單片機多機串口通訊的原理，給出程序設計流程與思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is Described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上傳時間： 2013-12-19
上傳用戶：tecman
介紹了當前普通標記機控制系統現狀及其存在缺點，給出氣動標記機及相頻修正PWM模式的工作原理。采用ATmega16單片機和USB轉換RS232接口器件CH341T實現驅動控制系統與PC的實時通訊，標記控制系統可升級到USB接口。采用基于ATmega16的相頻修正PWM替換555振蕩電路產生的PWM，可直接通過軟件調整PWM信號。使用達林頓三極管TIP122替代直流繼電器驅動高頻電磁閥，使得電磁閥驅動電路簡單，成本低廉。該控制系統已成功應用于氣動標記機。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are Described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
上傳時間： 2013-10-18
上傳用戶：1427796291
