Luminary Micro Stellaris™ microcontrollers that are equipped with an analog-to-digital converter(ADC), use an innovative sequence-based sampling architecture designed to be extremely flexible,yet easy to use. This application note describes the sampling architecture of the ADC. Sinceprogrammers can configure Stellaris microcontrollers either through the powerful StellarisFamilyDriver Library or through direct writes to the device's control registers, this application note describesboth methods. The information presented in this document is intended to complement the ADCchapter of the device datasheet, and assumes the reader has a basic understanding of howADCsfunction.
標簽： Microcontr Stellaris Using the
上傳時間： 2013-10-14
上傳用戶：blans
Applying power to a standard logic chip, SRAM, or EPROM, usually results in output pinstracking the applied voltage as it rises. Programmable logic attempts to emulate that behavior,but physics forbids perfect emulation, due to the device programmability. It requires care tospecify the pin behavior, because programmable parts encounter unknown variables – yourdesign and your power environment.
上傳時間： 2013-11-24
上傳用戶：253189838
TIMER.ASM ********* [ milindhp@tifrvax.tifr.res.in ] Set Processor configuration word as = 0000 0000 1010 b. a] -MCLR tied to VDD (internally). b] Code protection off. c] WDT disabled. d] Internal RC oscillator [4 MHZ].
標簽： configuration Processor milindhp tifrvax
上傳時間： 2015-05-24
上傳用戶：wqxstar
his project was built and tested with WinAVR-20060125. Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!! To build the code, just install WinAVR and run "make" from the console in echomaster and echoslave subdirs. "make program" will program the device if you have a AVRISP attached. Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST! Otherwise you wont get any clock signal to the AVR and then you can t program it or reset the fuses! The MC1319x has default clock output of 32kHz so you will have to set your programmer to a very low frequency (<=32kHz/4) to be able to program it while it is running on that!
標簽： the 20060125 project WinAVR
上傳時間： 2014-10-10
上傳用戶：yan2267246
藍牙協議This specification describes the Audio/Video Control Transport Protocol (AVCTP), which is used to transport command and response messages for controlling Audio Video features in conformant devices. This protocol enables a device to support more than one control profile at the same time each supported profile shall define its own message formatting and/or usage rules.
標簽： specification describes Transport Protocol
上傳時間： 2015-08-11
上傳用戶：大融融rr
This directory builds the Tape class driver for Microsoft® Windows® Server 2003. The class driver implements device-independent support, and exports support routines for device-specific tape miniclass drivers. It handles device-independent tape requests and calls the tape minidriver routines to process device-specific functions. Class driver splits transfer requests, when necessary, to fit the maximum transfer size for the underlying host bus adapter. It also provides device-independent, tape-specific error handling, and calls the tape miniclass driver s device-specific error handling routines.
標簽： class Microsoft directory reg
上傳時間： 2013-12-09
上傳用戶：huangld
Universal Serial Bus (USB) is a communications architecture that gives a personal computer (PC) the ability to interconnect a variety of devices using a simple four- wire cable. The USB is actually a two-wire serial communication link that runs at either 1.5 or 12 megabits per second (mbs). USB protocols can configure devices at startup or when they are plugged in at run time. These devices are broken into various device classes. Each device class defines the common behavior and protocols for devices that serve similar functions. Some examples of USB device classes are shown in the following table
標簽： communications architecture Universal computer
上傳時間： 2015-12-08
上傳用戶：stvnash
The XML Toolbox converts MATLAB data types (such as double, char, struct, complex, sparse, logical) of any level of nesting to XML format and vice versa. For example, >> project.name = MyProject >> project.id = 1234 >> project.param.a = 3.1415 >> project.param.b = 42 becomes with str=xml_format(project, off ) "<project> <name>MyProject</name> <id>1234</id> <param> <a>3.1415</a> <b>42</b> </param> </project>" On the other hand, if an XML string XStr is given, this can be converted easily to a MATLAB data type or structure V with the command V=xml_parse(XStr).
標簽： converts Toolbox complex logical
上傳時間： 2016-02-12
上傳用戶：a673761058
build a modbus client/server for use on the Protocessor (from FieldServer Technologies) Tools Required: 1. Microchip MCC18 compiler. 2. ICD2 debugger (or other device to program your PIC) 3. Protocessor hardware.
標簽： Technologies Protocessor FieldServer modbus
上傳時間： 2016-02-27
上傳用戶：wfeel
JRed is a 100％ Java implementation of the IrDA infrared communications protocols. JRed lets you beam objects from a PalmOS or Windows CE device to your Windows 95/98/NT or Linux PC.
標簽： JRed implementation communications protocols
上傳時間： 2013-12-11
上傳用戶：saharawalker
