The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The Device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上傳時間： 2013-10-10
上傳用戶：adada
單相橋式逆變電路為例：S1～S4是橋式電路的4個臂，由電力電子器件及輔助電路組成。S1、S4閉合，S2、S3斷開時，負載電壓uo為正S1；S1、S4斷開，S2、S3閉合時，uo為負，把直流電變成了交流電。改變兩組開關切換頻率，可改變輸出交流電頻率。圖5-1 逆變電路及其波形舉例電阻負載時，負載電流io和uo的波形相同，相位也相同。阻感負載時，io滯后于uo，波形也不同（圖5-1b）。t1前：S1、S4通，uo和io均為正。t1時刻斷開S1、S4，合上S2、S3，uo變負，但io不能立刻反向。io從電源負極流出，經S2、負載和S3流回正極，負載電感能量向電源反饋，io逐漸減小，t2時刻降為零，之后io才反向并增大 （2）換流方式分類換流——電流從一個支路向另一個支路轉移的過程，也稱換相。開通：適當?shù)拈T極驅動信號就可使其開通。關斷：全控型器件可通過門極關斷。半控型器件晶閘管，必須利用外部條件才能關斷，一般在晶閘管電流過零后施加一定時間反壓，才能關斷。研究換流方式主要是研究如何使器件關斷。本章?lián)Q流及換流方式問題最為全面集中，因此在本章講述1、器件換流利用全控型器件的自關斷能力進行換流（Device Commutation）。2、電網換流由電網提供換流電壓稱為電網換流（Line Commutation）。可控整流電路、交流調壓電路和采用相控方式的交交變頻電路，不需器件具有門極可關斷能力，也不需要為換流附加元件。3、負載換流由負載提供換流電壓稱為負載換流（Load Commutation）。負載電流相位超前于負載電壓的場合，都可實現負載換流。負載為電容性負載時，負載為同步電動機時，可實現負載換流。
上傳時間： 2013-10-15
上傳用戶：qingdou
msp430單片機
標簽： Erratasheet 14x x14 Device
上傳時間： 2013-10-19
上傳用戶：dick_sh
數字控制的交流調速系統所選用的微處理器、功率器件及產生PWM波的方法是影響交流調速系統性能好壞的直接因素。在介紹了正弦脈寬調制(SPWM)技術的基礎上，設計了一種以8098單片機作為控制器，以智能功率模塊IPM為開關器件的變頻調速系統。通過軟件編程，產生正弦脈沖寬度調制波形來控制絕緣柵雙極晶體管的導通和關斷，從而達到控制異步電動機轉速的目的。實驗結果表明，該系統可調頻率調電壓，穩定度高，調速范圍寬，具有較強的實用價值 Abstract: AC variable speed with digital control systems used microprocessors， power Devices and generate PWM wave is the direct factors of affecting the performance AC speed regulation system. On the basis of introducing the sinusoidal pulse width modulation (SPWM) technology，this paper designed variable speed system which used 8098 as a controller， intelligent power module IPM as switching Device. Through software programming， resulting in sinusoidal pulse width modulation waveform to control the insulated gate bipolar transistor turn on and off， so as to achieve the purpose of speed control of induction motors. Experimental results show that the system can adjust frequency modulation voltage， high stability， wide speed range， has a strong practical value.
標簽： 8098 SPWM 單片機 變頻調速系統
上傳時間： 2013-11-14
上傳用戶：ynwbosss
利用單片機具有的智能程序控制的特點，設計了基于STC89C52單片機的"二極管特性測試器"，可對二極管一般特性進行快速測試。通過穩定線性電流源給二極管加載恒定電流，然后由高精度模數轉換器測試其壓降，以此為基礎可判斷二極管好壞、檢測二極管極性和測試二極管伏安特性等，避免了用萬用表測試只能測得極性而不知其特性這一缺點。可用于電子設計制作過程中對二極管進行快速測試，以確定被測二極管是否滿足電路的設計要求。 Abstract: By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This Device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
上傳時間： 2013-11-13
上傳用戶：assef
Designing read/write Device (RWD) units for industrial RF-Identification applications is strongly facilitated by the NXP Semiconductors HITAG Reader Chip HTRC110. All needed function blocks, like the antenna driver, modulator demodulator and antenna diagnosis unit, are integrated in the HTRC110. Therefore only a minimum number of additional passive components are required for a complete RWD. This Application Note describes how to design an industrial RF-Identification system with the HTRC110. The major focus is dimensioning of the antenna, all other external components including clock and power supply, as well as the demodulation principle and its implementatio
上傳時間： 2013-10-22
上傳用戶：zhengjian
Digitemp Junior – An RS-232 Port-Powered Digital Thermometer Digitemp Jr. is a Device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it rel- atively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power sup- plies or batteries. It is powered directly by the RS-232 port.
標簽： Microchip 232 PIC RS
上傳時間： 2013-10-21
上傳用戶：baitouyu
為解決電致變色器件的顏色變化受外界環境顏色控制的問題，設計了一種基于單片機的便攜式顏色自適應識別電路。與傳統顏色識別電路相比較，該電路利用數字式的顏色傳感器來獲取外界環境顏色，產生的數字顏色信號易于單片機進行處理。在電路中，下位機部分主要負責獲取電致變色器件變色參數及控制電致變色器件的顏色變化;而上位機部分主要負責把下位機獲取的電致變色器件變色參數進行電壓到顏色的曲線擬合，并通過藍牙通信把擬合曲線參數傳遞給下位機。結果表明，該電路能自動根據環境顏色提供-4~4 V范圍步進為0.1 V的電壓來驅動電致變色器件的顏色顯示，與傳統的顏色識別電路設計相比，識別的精度和速度都得到了明顯改善。 Abstract: In this paper， a portable adaptive circuit for color identification(PACCI) based on MCU was designed. Compared to the traditional color identification circuit， the PACCI adopts digital sensor to detect the color data from external environment and further generate digital color data， which can be processed easily by MCU. In PACCI， the slave is mainly responsible for detecting the color parameters of the corresponding elcreochromic Device and further driving it. For the master， which is mainly responsible for the color curve fitting based on the parameters of the electrochromic Device， and transmits the fitting parameters to the slave through the bluetooth Device. The results show that the PACCI can provide the basis voltage range from -4V to 4V automatically based on the colors of external environment with step as 0.1V to drive the corresponding electrochromic Device. Compared to the traditional color recognition circuit， the recognition accuracy and speed of PACCI have been improved significantly.
上傳時間： 2013-11-09
上傳用戶：franktu
Digitemp Jr. is a Device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上傳時間： 2013-10-20
上傳用戶：Maple
以太網和CAN總線應用廣泛，但由于其通信協議不同，兩種總線器件間無法進行數據通信，因此，設計了基于CP2200與C8051F040的以太網總線與CAN總線接口轉換電路，并給出部分相關硬件電路與軟件設計分析。在保證數據完整和協議可靠的前提下，通過握手協議和簡化的以太網協議，不僅實現了以太網數據與CAN數據的轉發，同時還順利的解決了以太網的高速性與CAN的低速率沖突，以及兩者數據包之間的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating between two kinds of bus Device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
標簽： C8051F040 CAN 以太網 轉換
上傳時間： 2013-10-15
上傳用戶：Ants
蟲蟲下載站版權所有 京ICP備2021023401號-1
