The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware Environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
The 87LPC76X Microcontroller combines in a small package thebenefits of a high-performance microcontroller with on-boardhardware supporting the Inter-Integrated Circuit (I2C) bus interface.The 87LPC76X can be programmed both as an I2C bus master, aslave, or both. An overview of the I2C bus and description of the bussupport hardware in the 87LPC76X microcontrollers appears inapplication note AN464, Using the 87LPC76X Microcontroller as anI2C Bus Master. That application note includes a programmingexample, demonstrating a bus-master code. Here we show anexample of programming the microcontroller as an I2C slave.The code listing demonstrates communications routines for the87LPC76X as a slave on the I2C bus. It compliments the program inAN464 which demonstrates the 87LPC76X as an I2C bus master.One may demonstrate two 87LPC76X devices communicating witheach other on the I2C bus, using the AN464 code in one, and theprogram presented here in the other. The examples presented hereand in AN464 allow the 87LPC76X to be either a master or a slave,but not both. Switching between master and slave roles in amultimaster Environment is described in application note AN435.The software for a slave on the bus is relatively simple, as theprocessor plays a relatively passive role. It does not initiate bustransfers on its own, but responds to a master initiating thecommunications. This is true whether the slave receives or transmitsdata—transmission takes place only as a response to a busmaster’s request. The slave does not have to worry about arbitrationor about devices which do not acknowledge their address. As theslave is not supposed to take control of the bus, we do not demandit to resolve bus exceptions or “hangups”. If the bus becomesinactive the processor simply withdraws, not interfering with themaster (or masters) on the bus which should (hopefully) try toresolve the situation.
上傳時間： 2013-11-19
上傳用戶：shirleyYim
單片機系統“PC”失控的軟件措施Software Measure of GettingO uto fC ontrolfo r“PC"in S ingleC hipC omputerS ystem謐 加 春 王 曉 基 雷 小 華(江 西 理 工 大 學機 電 工 程 學 院 ，贛 州 34 10 00)摘要單片機系統在實際工業現場中可能遇到各種干擾和自身的隨機性故障。現場惡劣的環境有可能使計算機系統發生異常，計算機程序指針“PC”失控就是常見的故障之一，如果發生“PC”失控，將導致CPI工作混亂，釀成嚴重的事故。研究了“PC”失控的原因，并指出軟件抗干擾的幾種方法，有效保證單片機系統的正常工作。關鍵詞單片機“PC”失控抗干擾Abstract Inp racticalin dustrialfi elds,th ereis v ariousin terferencea fectingo perationo fsi nglec hipc omputersy stemsa ndt hec omputersy stems。fac噸random faults飾themselves. It is very common that the severe Environment makes the computer systems abnormal. The program counter "PC"gettingo utof co ntorlis on eo fth ec ommonfa ults.If th isoc curs,C PUw ouldb eru nningo utof or deran din torducesse riousan cient.T hec ausesof " PC"geting out of control， studied in this paper and some countermeasures of anti-interference師software are given to ensure single chip computer systemworking properly.Keywords Single。飾computer Porgramc ounter"P C" Anti-interfeernc 在設 計 和 開發單片機系統時，一般難以周全地預計單片機系統在實際工業現場中可能遇到的各種干擾和自身的隨機性故障。因此，除了采取防止和抑制干擾的各項措施外，還應該借助于軟件措施克服某些干擾，系統還應具備迅速自行恢復的能力。本文介紹的應對單片機系統PC失控的軟件措施，設計靈活，節省硬件資源，能保證測控系統長期可靠地運行。MC S- 5 1單片機以其優良的性能價格比大量應用于工業現場測試和控制領域。但是，現場惡劣的環境有可能使計算機系統發生異常，計算機程序指針PC失控就是常見的故障之一，一旦發生PC“走飛”，計算機系統就會出現工作混亂，釀成嚴重的事故。為 了 在 CP 失控時盡量減少由此帶來的不利影響，并盡快使系統恢復正常，需要采取一定的軟件措施和硬件措施。常見的硬件措施有“看門狗”電路。軟件措施設置的前提條件是:①在干擾作用下，微機系統硬件部分不會受到任何損壞，或者損壞部分設置有監測狀態可供查詢;②程序區不會受到干擾侵害。單片機系統的程序和表格以及重要的參數均設置在ROM區，不會因干擾的侵人而改變;③ RAM區中的重要數據不會被破壞，或者雖然被破壞，但是可以重新建立。
標簽： 單片機系統 軟件
上傳時間： 2013-11-02
上傳用戶：bhqrd30
This application note contains a reference design consisting of HDL IP and Xilinx AdvancedConfiguration Environment (ACE) software utilities that give designers great flexibility increating in-system programming (ISP) solutions. In-system programming support allowsdesigners to revise existing designs, package the new bitstream programming files with theprovided software utilities, and update the remote system through the JTAG interface using theEmbedded JTAG ACE Player.
上傳時間： 2013-11-14
上傳用戶：JIMMYCB001
WP369可擴展式處理平臺-各種嵌入式系統的理想解決方案 ：Delivering unrivaled levels of system performance,flexibility, scalability, and integration to developers,Xilinx's architecture for a new Extensible Processing Platform is optimized for system power, cost, and size. Based on ARM's dual-core Cortex™-A9 MPCore processors and Xilinx’s 28 nm programmable logic,the Extensible Processing Platform takes a processor-centric approach by defining a comprehensive processor system implemented with standard design methods. This approach provides Software Developers a familiar programming Environment within an optimized, full featured,powerful, yet low-cost, low-power processing platform.
上傳時間： 2013-10-22
上傳用戶：685
The use of the Wind River VxWorks Real-Time Operating System (RTOS) on Virtex™-4embedded PowerPC™ processors continues to be a popular choice for high performanceFPGA designs. The introduction of the Wind River Workbench design Environment has enableda new and easier way for designers to control the configuration of the VxWorks kernel. Thisguide shows the steps required to build and configure a ML403 Embedded DevelopmentPlatform to boot and run the VxWorks RTOS. A VxWorks bootloader is created, programmedinto Flash, and used to boot the design. The concepts presented here can be scaled to anyPowerPC enabled development platform.
上傳時間： 2013-10-26
上傳用戶：agent
在研究傳統家用燃氣報警器的基礎上，以ZigBee協議為平臺，構建mesh網狀網絡實現網絡化的智能語音報警系統。由于傳感器本身的溫度和實際環境溫度的影響，傳感器標定后采用軟件補償方法。為了減少系統費用，前端節點采用半功能節點設備，路由器和協調器采用全功能節點設備，構建mesh網絡所形成的家庭內部報警系統，通過通用的電話接口連接到外部的公用電話網絡，啟動語音模塊進行報警。實驗結果表明，在2.4 GHz頻率下傳輸，有墻等障礙物的情況下，節點的傳輸距離大約為35 m，能夠滿足家庭需要，且系統工作穩定，但在功耗方面仍需進一步改善。 Abstract: On the basis of studying traditional household gas alarm system, this paper proposed the platform for the ZigBee protocol，and constructed mesh network to achieve network-based intelligent voice alarm system. Because of the sensor temperature and the actual Environment temperature, this system design used software compensation after calibrating sensor. In order to reduce system cost, semi-functional node devices were used as front-end node, however, full-function devices were used as routers and coordinator，constructed alarm system within the family by building mesh network，connected to the external public telephone network through the common telephone interface, started the voice alarm module. The results indicate that nodes transmit about 35m in the distance in case of walls and other obstacles by 2.4GHz frequency transmission, this is able to meet family needs and work steadily, but still needs further improvement in power consumption.
標簽： ZigBee 無線智能 家 報警系統
上傳時間： 2013-10-30
上傳用戶：swaylong
解壓包包含了C語言入門經典教程和Visuak c++軟件 【基本簡介】 Visual C++是一個功能強大的可視化軟件開發工具。自1993年Microsoft公司推出Visual C++1.0后，隨著其新版本的不斷問世，Visual C++已成為專業程序員進行軟件開發的首選工具。 雖然微軟公司推出了Visual C++.NET(Visual C++7.0)，但它的應用的很大的局限性，只適用于Windows 2000,Windows XP和Windows NT4.0。所以實際中，更多的是以Visual C++6.0為平臺。 Visual C++6.0不僅是一個C++編譯器，而且是一個基于Windows操作系統的可視化集成開發環境（integrated development Environment,IDE）。Visual C++6.0由許多組件組成，包括編輯器、調試器以及程序向導AppWizard、類向導Class Wizard等開發工具。 這些組件通過一個名為Developer Studio的組件集成為和諧的開發環境。 在Visual C++ 6.0 企業版的基礎上集成官方的SP6升級補丁制作而成！免序列號，安裝完即可使用，無需再打補丁！ 【使用方法】 有些朋友反應在安裝后出現 "Error spawning error" 可以看看下面綠色軟件找到的一些解決方案： 點擊VC“TOOLS（工具）”—>“Option（選擇）”—>“Directories（目錄）”重新設置“Excutable Fils、Include Files、Library Files、Source Files”的路徑。很多情況可能就一個盤符的不同（例如你的VC裝在C，但是這些路徑全部在D），改過來就OK了。
上傳時間： 2013-10-09
上傳用戶：hui626493
This application note contains a reference design consisting of HDL IP and Xilinx AdvancedConfiguration Environment (ACE) software utilities that give designers great flexibility increating in-system programming (ISP) solutions. In-system programming support allowsdesigners to revise existing designs, package the new bitstream programming files with theprovided software utilities, and update the remote system through the JTAG interface using theEmbedded JTAG ACE Player.
上傳時間： 2013-10-22
上傳用戶：gai928943
Applying power to a standard logic chip, SRAM, or EPROM, usually results in output pinstracking the applied voltage as it rises. Programmable logic attempts to emulate that behavior,but physics forbids perfect emulation, due to the device programmability. It requires care tospecify the pin behavior, because programmable parts encounter unknown variables – yourdesign and your power Environment.
上傳時間： 2013-11-24
上傳用戶：253189838
