Abstract: The MAX9930–MAX9933 family of RF controllers and detector can be used in a wide variety of applications. Anideal application is cable television (CATV) over Fiber, where either a RF controller or a RF detector controls the gain of atransimpedance amplifier (TIA). This application note shows how the MAX9930 (RF controller) can be used as either theRF controller or detector.
A large group of Fiber optic lasers are powered by DCcurrent. Laser drive is supplied by a current source withmodulation added further along the signal path. Thecurrent source, although conceptually simple, constitutesan extraordinarily tricky design problem. There are anumber of practical requirements for a Fiber optic currentsource and failure to consider them can cause laser and/or optical component destruction.
波長信號的解調是實現光纖光柵傳感網絡的關鍵,基于現有的光纖光柵傳感器解調方法,提出一種基于FPGA的雙匹配光纖光柵解調方法,此系統是一種高速率、高精度、低成本的解調系統,并且通過引入雙匹配光柵有效地克服了雙值問題同時擴大了檢測范圍。分析了光纖光柵的測溫原理并給出了該方案軟硬件設計,綜合考慮系統的解調精度和FPGA的處理速度給出了基于拉格朗日的曲線擬合算法。
Abstract:
Sensor is one of the most important application of the Fiber grating. Wavelength signal demodulating is the key techniques to carry out Fiber grating sensing network, based on several existing methods of Fiber grating sensor demodulation inadequate, a two-match Fiber grating demodulation method was presented. This system is a high-speed, high precision, low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of Fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA,this paper gives the curve fitting algorithm based on Lagrange.
通過比較各種隔離數字通信的特點和應用范圍,指出塑料光纖在隔離數字通信中的優勢。使用已經標準化的TOSLINK接口,有利于節省硬件開發成本和簡化設計難度。給出了塑料光纖的硬件驅動電路,說明設計過程中的注意事項,對光收發模塊的電壓特性和頻率特性進行全面試驗,并給出SPI口使用塑料光纖隔離通信的典型應用電路圖。試驗結果表明,該設計可為電力現場、電力電子及儀器儀表的設計提供參考。
Abstract:
y comparing characteristics and applications area of various isolated digital communications, this article indicates advantages of plastic optical Fiber in isolated digital communications. Using the standardized TOSLINK interface, it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical Fiber module, explains the noticed details in design process, gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally,it gives typical application circuit of the SPI communication port by using plastic optical Fiber isolation .The results show that this design can be referenced for the power field, power electronics and instrumentation design.
波長信號的解調是實現光纖光柵傳感網絡的關鍵,基于現有的光纖光柵傳感器解調方法,提出一種基于FPGA的雙匹配光纖光柵解調方法,此系統是一種高速率、高精度、低成本的解調系統,并且通過引入雙匹配光柵有效地克服了雙值問題同時擴大了檢測范圍。分析了光纖光柵的測溫原理并給出了該方案軟硬件設計,綜合考慮系統的解調精度和FPGA的處理速度給出了基于拉格朗日的曲線擬合算法。
Abstract:
Sensor is one of the most important application of the Fiber grating. Wavelength signal demodulating is the key techniques to carry out Fiber grating sensing network, based on several existing methods of Fiber grating sensor demodulation inadequate, a two-match Fiber grating demodulation method was presented. This system is a high-speed, high precision, low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of Fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA,this paper gives the curve fitting algorithm based on Lagrange.
ADM6993F/FXFiber to Fast Ethernet Converter (TS1000 CPE Complied)
The ADM6993F/FX is a single chip integrating two 10/100 Mbps MDIX TX/FX transceivers, a three-port 10/100M Ethernet L2 switch controller, and one OAM engine to meet demanding applications, including Fiber-to-Ethernet media converters, especially the Fiber to the home (FTTH) media converters. The ADM6993F/FX feature set includes link pass through (LPT), TS1000 OAM frame receiving/processing/transmitting, programmable link status LED display, various loop-back modes, and one configurable MII ports for snooping/inserting OAM frame from/to 100Fx. The ADM6993FX is the environmentally friendly “green” package version.
The CommScope InstaPATCH? 360 and ReadyPATCH? solutions utilize a
standards-compliant multi-Fiber connector to provide high density termination
capability. The connector is called an MPO (Multi-Fiber Push On) connector by
the standards. In many cases, multi-Fiber connector products are referred to as
MTP connectors. This document is intended to clarify the difference between the two terms – MPO and MTP.