本文將接續介紹電源與功率電路基板，以及數字電路基板導線設計。寬帶與高頻電路基板導線設計a.輸入阻抗1MHz，平滑性(flatness)50MHz 的OP增幅器電路基板圖26 是由FET 輸入的高速OP 增幅器OPA656 構成的高輸入阻抗OP 增幅電路，它的gain取決于R1、R2，本電路圖的電路定數為2 倍。此外為改善平滑性特別追加設置可以加大噪訊gain，抑制gain-頻率特性高頻領域時峰值的R3。圖26 高輸入阻抗的寬帶OP增幅電路圖27 是高輸入阻抗OP 增幅器的電路基板圖案。降低高速OP 增幅器反相輸入端子與接地之間的浮游容量非常重要，所以本電路的浮游容量設計目標低于0.5pF。如果上述部位附著大浮游容量的話，會成為高頻領域的頻率特性產生峰值的原因，嚴重時頻率甚至會因為feedback 阻抗與浮游容量，造成feedback 信號的位相延遲，最后導致頻率特性產生波動現象。此外高輸入阻抗OP 增幅器輸入部位的浮游容量也逐漸成為問題，圖27 的電路基板圖案的非反相輸入端子部位無full ground設計，如果有外部噪訊干擾之虞時，接地可設計成網格狀(mesh)。圖28 是根據圖26 制成的OP 增幅器Gain－頻率特性測試結果，由圖可知即使接近50MHz頻率特性非常平滑，-3dB cutoff頻率大約是133MHz。
標簽： PCB
上傳時間： 2013-11-13
上傳用戶：hebanlian
The LTP5900 includes sufficient power supply filtering and decoupling capacitancesuch that additional filtering should not be necessary for most battery-powereddesigns. Care must be taken to avoid large transient voltages on the supply as theM2510 steps up its current consumption (see the section on Supply Design below).
標簽： Integration Hardware Guide 5900
上傳時間： 2014-12-24
上傳用戶：youmo81
The LTP5901 and LTP5902 require little external circuitry, as the devices references,decoupling and power supply filtering are integrated. The LTP5901 and LTP5902 will bemodularly certified for operation in the United States (FCC), Canada (IC) and theEuropean Union (CE).
標簽： Integration LTP Hardware Guide
上傳時間： 2013-11-22
上傳用戶：sunchao524
We provide complete power solutions with a full lineup of power managementproducts. This brochure provides an overview of our high performance DC/DC switching regulatorcontrollers for applications including datacom, telecom, industrial, automotive, medical, avionicsand control systems. We make power design easier with our industry-leading field applicationengineering support; a broad selection of demonstration boards with schematics, layout filesand parts lists; SwitcherCAD® software for simulation, application notes and comprehensivetechnical documentation.
上傳時間： 2013-10-15
上傳用戶：lz4v4
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
標簽： MAXREFDES Lakewood Isolated Output
上傳時間： 2013-11-02
上傳用戶：fengzimili
Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.
標簽： Riverside MAXREFDES Isolated Output
上傳時間： 2013-11-16
上傳用戶：會稽劍客
Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
上傳時間： 2013-10-12
上傳用戶：jinyao
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上傳時間： 2013-11-18
上傳用戶：hulee
Permission to make digital or hard copies of all or part of this work forpersonal or classroom use is granted without fee provided that copies arenot made or distributed for profit or commercial advantage and that copiesbear this notice and the full citation on the first page. To copy otherwise, torepublish, to post on servers or to redistribute to lists, requires prior specificpermission.
標簽： 數字電源
上傳時間： 2013-10-16
上傳用戶：dddddd
Features: High efficiency, high reliability, low cost AC input range selected by switch 100% full load burn-in test Protections: Short circuit / Over load Fixed switching frequency at 25KHz Cooling by free air convection 1 year warranty Dimensions: 199*98*38mm (L*W*H)
標簽： Switchin Output Single SKS
上傳時間： 2013-10-30
上傳用戶：taa123456
