The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
This document describes part number speciÞc changes to recommended operating conditions and revised electrical speciÞcations,as applicable, from those described in the generalMPC7400 Hardware SpeciÞcations.SpeciÞcations provided in this Part Number SpeciÞcation supersede those in theMPC7400 Hardware SpeciÞcationsdated 9/99(order #: MPC7400EC/D) for these part numbers only; speciÞcations not addressed herein are unchanged. This document isfrequently updated, refer to the website at http://www.mot.com/SPS/PowerPC/ for the latest version.Note that headings and table numbers in this data sheet are not consecutively numbered. They are intended to correspond to theheading or table affected in the general hardware speciÞcation.Part numbers addressed in this document are listed in Table A. For more detailed ordering information see Table B.
This program is free software you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
數字運算，判斷一個數是否接近素數
A Niven number is a number such that the sum of its digits divides itself. For example, 111 is a Niven number because the sum of its digits is 3, which divides 111. We can also specify a number in another base b, and a number in base b is a Niven number if the sum of its digits divides its value.
Given b (2 <= b <= 10) and a number in base b, determine whether it is a Niven number or not.
Input
Each line of input contains the base b, followed by a string of digits representing a positive integer in that base. There are no leading zeroes. The input is terminated by a line consisting of 0 alone.
Output
For each case, print "yes" on a line if the given number is a Niven number, and "no" otherwise.
Sample Input
10 111
2 110
10 123
6 1000
8 2314
0
Sample Output
yes
yes
no
yes
no
his project was built and tested with WinAVR-20060125.
Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!!
To build the code, just install WinAVR and run "make" from the console in echomaster and
echoslave subdirs.
"make program" will program the device if you have a AVRISP attached.
Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock
from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST!
Otherwise you wont get any clock signal to the AVR and then you can t program it or reset
the fuses!
The MC1319x has default clock output of 32kHz so you will have to set your programmer to
a very low frequency (<=32kHz/4) to be able to program it while it is running on that!
pop3代理服務器源代碼One of the most powerful features of Pop3 Agent is a naive Bayes filter,
that is capable of recognizing spam e-mails after appropriate training.
Pop3 Agent uses an embedded Firebird database server. Of course, you can
configure Pop3 Agent to work with an existing server if there is another
Interbase/Firebird installation available in your network. Open the Pop3 Agent
home directory, delete or rename gds32.dll and ib_util.dll, and set the
INI file parameter FBembedded=0.
Implemented BFS, DFS and A*
To compile this project, use the following command:
g++ -o search main.cpp
Then you can run it:
./search
The input is loaded from a input file in.txt
Here is the format of the input file:
The first line of the input file shoud contain two chars indicate the source and destination city for breadth first and depth first algorithm.
The second line of input file shoud be an integer m indicate the number of connections for the map.
Following m lines describe the map, each line represents to one connection in this form: dist city1 city2, which means there is a connection between city1 and city2 with the distance dist.
The following input are for A*
The following line contains two chars indicate the source and destination city for A* algorithm.
Then there is an integer h indicate the number of heuristic.
The following h lines is in the form: city dist which means the straight-line distance from the city to B is dist.
The programming port of all the FP PLC’s support OPEN MEWTOCOL-COM. This is very useful when you want to monitor PLC values/bits or to set PLC values or bits via your COMPUTER. You can use any language such as Basic, C, Pascal, Assembler or even if other suppliers of PLCs can send ASCII strings, they can talk to our PLCs to exchange data.
This program is free software you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation either version 2
of the License, or (at your option) any later version.
