實驗源代碼
//Warshall.cpp #include<stdio.h> void warshall(int k,int n) { int i , j, t; int temp[20][20]; for(int a=0;a<k;a++) { printf("請輸入矩陣第%d 行元素:",a); for(int b=0;b<n;b++) { scanf ("%d",&temp[a][b]); } } for(i=0;i<k;i++){ for( j=0;j<k;j++){ if(temp[ j][i]==1) { for(t=0;t<n;t++) { temp[ j][t]=temp[i][t]||temp[ j][t]; } } } } printf("可傳遞閉包關系矩陣是:\n"); for(i=0;i<k;i++) { for( j=0;j<n;j++) { printf("%d", temp[i][ j]); } printf("\n"); } } void main() { printf("利用 Warshall 算法求二元關系的可傳遞閉包\n"); void warshall(int,int); int k , n; printf("請輸入矩陣的行數 i: "); scanf("%d",&k);
四川大學實驗報告 printf("請輸入矩陣的列數 j: "); scanf("%d",&n); warshall(k,n); }
標簽：
warshall
離散
實驗
上傳時間：
2016-06-27
上傳用戶：梁雪文以
數字示波器功能強大,使用方便,但是價格相對昂貴。本文以Ti的MSP430F5529為主控器,以Altera公司的EP2C5T144C8 FPGA器件為邏輯控制部件設計數字示波器。模擬信號經程控放大、整形電路后形成方波信號送至FPGA測頻,根據頻率值選擇采用片上及片外高速AD分段采樣。FPGA控制片外AD采樣并將數據輸入到FIFO模塊中緩存,由單片機進行頻譜分析。測試表明:簡易示波器可以實現自動選檔、多采樣率采樣、高精度測頻及頻譜分析等功能。Digital oscilloscope is powerful and easy to use, but also expensive. The research group designed a low-cost digital oscilloscope, the chip of MSP430F5529 of TI is chosen as the main controller and the device of EP2C5T144C8 of Altera company is used as the logic control unit. Analog signal enter the programmable amplifier circuit, shaping circuit and other pre-processing circuit. The shaped rectangular wave signal is sent to FPGA for measure the frequency. According to the frequency value to select AD on-chip or off-chip high-speed AD for sampling. FPGA controls the off-chip AD sampling and buffers AD data by FIFO module. The single chip microcomputer receives the data, and do FFT for spectrum analysis. The test shows that the simple oscilloscope can realize automatic gain selection, sampling at different sampling rates, high precision frequency measurement and spectrum analysis.
標簽：
msp430
單片機
fpga
數字示波器
上傳時間：
2022-03-27
上傳用戶：
數字頻率計是電工電子中常用的測量儀器,數字頻率計通過用輸入待測信號對一特定長度的信號進行計數,從而得出頻率并通過數碼管直觀的顯示出來。本文提出了一種與輸入同步的數字頻率計的設計,提高了頻率計的精度,設計采用Multisim軟件進行設計和仿真的過程,介紹了其工作原理,硬件電路設計和仿真的過程。設計采用了Multisim軟件進行設計和仿真,設計結果得到的驗證。Digital frequency counter is used to measure the frequency of a signal.It is common to use a multivibrator to generate a standard 1 second time base signal and count input signal gated by this signal.However,the asynchronous of this time base signal with input signal will bring errors.In this paper,a high precision frequency counter which use synchronized time base signal generator is proposed.This frequency counter is designed and simulated by Multisim tools and result is verified.
標簽：
multisim
上傳時間：
2022-05-08
上傳用戶：
