在開放式數控系統結構模型的基礎上，研究了基于ISA總線的DSP通信控制原理。采用中斷方式完成了PC機和DSP之間的通信。介紹了以DriverWorks為工具開發ISA設備WDM驅動程序的方法，探討了中斷處理、驅動程序與應用程序之間的通信,簡要說明了驅動程序的安裝與調試。通過調試,系統設計運行穩定。
Abstract:
The ISA bus and DSP correspondence control principle is investigated in the basis of the existing open architecture numerical control system.The interrupt method is used to realize the communication between PC and DSP based on the ISA bus.The methods of WDM driver exploitation for ISA device using Driver Works are introduced.The main process of driver program and the keys such as handle interrupt and the communication between the drivers and application are presented.And how to debug and install the drive is explained.
C8051F020單片機通過SPI接口驅動四線電阻式觸摸屏控制器TSC2046，利用中斷方式驅動TSC2046設計軟件。介紹了觸摸屏的工作原理、TSC2046工作方式以及典型應用電路。
Abstract:
The C8051F020 MCU is connected with the TSC2046 which is a 4-wire touch screen controller. The TSC2046 is controlled by interrupt mode, the? operation principle of touch screen is introduced. The operation mode of TSC2046 and typical application circuit are also discussed.
介紹了一種基于AT89S52微處理器、鍵控顯示模式、多漢字顯示的顯示模塊設計方法。對AT89S52的內部功能及使用高128字節RAM時的尋址方式進行說明。給出了四漢字顯示模塊的硬件電路原理圖、主程序流程圖以及中斷顯示流程圖。
Abstract:
The design method of display module base on the AT89S52 microcontroller,display mode controlled by keyboard and? showing several Chinese characterses are introduced in the paper.The internal function and the addressing mode for the high 128B RAM of the AT89S52 are explained.The basic circuit diagram,the main program flow chart and the display interrupt flow chart of four Chinese characterses display module are also given.
介紹了MPC555與CS8900A擴展以太網的硬件設計圖。以NUCLUES PLUS操作系統為基礎，介紹了網卡軟件驅動程序的編制，給出了以太網協議包嵌入NUCLEUS PLUS操作系統的實現方法。
Abstract:
The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
利用AT89C51型單片機定時和中斷功能，配以LM386型音頻功率放大器，構成了作息號音自動播放器，為學校和機關管理提供方便。
Abstract:
Using timing and interrupt function of the AT89C51 single-chip microcomputer and the LM386 audio power amplifier.It is constituted the automatic bugle player.This player facilitates the institution and the school daily management.
FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power supplySoftware and hardware controlled power-down48-lead TQFP/EP packageSupport for 5 V input levels on most digital inputsPLL REFCLK multiplier (4× to 20×)Internal oscillator; can be driven by a single crystalPhase modulation capabilityMultichip synchronization
The PCA9537 is a 10-pin CMOS device that provides 4 bits of General Purpose parallelInput/Output (GPIO) expansion with interrupt and reset for I2C-bus/SMBus applicationsand was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders.I/O expanders provide a simple solution when additional I/O is needed for ACPI powerswitches, sensors, push-buttons, LEDs, fans, etc.
The PCA9538 is a 16-pin CMOS device that provides 8 bits of General Purpose parallelInput/Output (GPIO) expansion with interrupt and reset for I2C-bus/SMBus applicationsand was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders.I/O expanders provide a simple solution when additional I/O is needed for ACPI powerswitches, sensors, push-buttons, LEDs, fans, etc.
The PCA9539; PCA9539R is a 24-pin CMOS device that provides 16 bits of GeneralPurpose parallel Input/Output (GPIO) expansion with interrupt and reset forI2C-bus/SMBus applications and was developed to enhance the NXP Semiconductorsfamily of I2C-bus I/O expanders. I/O expanders provide a simple solution when additionalI/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
