基于TMS320F2812 光伏并網發電模擬裝置PROTEL設計原理圖+PCB+軟件源碼+WORD論文文檔,硬件采用2層板設計，PROTEL99SE 設計的工程文件，包括完整的原理圖和PCB文件，可以做為你的學習設計參考。 摘要：本文實現了一個基于TMS320F2812 DSP芯片的光伏并網發電模擬裝置，采用直流穩壓源和滑動變阻器來模擬光伏電池。通過TMS320F2812 DSP芯片ADC模塊實時采樣模擬電網電壓的正弦參考信號、光伏電池輸出電壓、負載電壓電流反饋信號等。經過數據處理后，用PWM模塊產生實時的SPWM 波，控制MOSFET逆變全橋輸出正弦波。本文用PI控制算法實現了輸出信號對給定模擬電網電壓的正弦參考信號的頻率和相位跟蹤，用恒定電壓法實現了光伏電池最大功率點跟蹤（MPPT），從而達到模擬并網的效果。另外本裝置還實現了光伏電池輸出欠壓、負載過流保護功能以及光伏電池輸出欠壓、過流保護自恢復功能、聲光報警功能、孤島效應的檢測、保護與自恢復功能。系統測試結果表明本設計完全滿定設計要求。關鍵詞：光伏并網，MPPT，DSP Photovoltaic Grid-connected generation simulator Zhangyuxin，Tantiancheng，Xiewuyang(College of Electrical Engineering, Chongqing University)Abstract: This paper presents a photovoltaic grid-connected generation simulator which is based on TMS320F2812 DSP, with a DC voltage source and a variable resistor to simulate the characteristic of photovoltaic cells. We use the internal AD converter to real-time sampling the referenced grid voltage signal, outputting voltage of photovoltaic, feedback outputting voltage and current signal. The PWM module generates SVPWM according to the calculation of the real-time sampling data, to control the full MOSFET INVERTER bridge output sine wave. We realized that the output voltage of the simulator can track the frequency and phase of the referenced grid voltage with PI regulation, and the maximum photovoltaic power tracking with constant voltage regulation, thereby achieved the purpose of grid-connected simulation. Additionally, this device has the over-voltage and over-current protection, audible and visual alarm, islanding detecting and protection, and it can recover automatically. The testing shows that our design is feasible.Keywords: Photovoltaic Grid-connected，MPPT，DSP 目錄引言 11. 方案論證 11.1. 總體介紹 11.2. 光伏電池模擬裝置 11.3. DC-AC逆變橋 11.4. MOSFET驅動電路方案 21.5. 逆變電路的變頻控制方案 22. 理論分析與計算 22.1. SPWM產生 22.1.1. 規則采樣法 22.1.2. SPWM 脈沖的計算公式 32.1.3. SPWM 脈沖計算公式中的參數計算 32.1.4. TMS320F2812 DSP控制器的事件管理單元 42.1.5. 軟件設計方法 62.2. MPPT的控制方法與參數計算 72.3. 同頻、同相的控制方法和參數計算 8
標簽：
tms320f2812
光伏
并網發電
模擬
protel
pcb
上傳時間：
2021-11-02
上傳用戶：
以STM32F103C8T6為核心,設計了無刷直流電機控制器硬件電路。電路主要包括IR2310構成的PWM驅動電路、IRF3808構成的逆變電路、增量式旋轉編碼構成的速度反饋電路。控制器具有CAN和RS232通信接口,可與計算機或PLC構成速度或位置伺服系統。利用由xPC目標搭建的半實物仿真平臺對PI參數進行整定。測試了控制器的速度伺服響應性能,給定速度為2400rpm時,控制器響應時間為0.32s。實驗結果表明,系統工作可靠,穩定性好,響應速度快,可以滿足上肢康復機器人的機械臂速度控制性能要求。The hardware circuit of Brushless DC motor controller is designed by taking STM32F103C8T6 as the core,which mainly includes PWM driving circuits made up of IR2310,INVERTER circuit formed by IRF3808,speed feedback circuit composed of incremental rotary encoder and so on.Speed servo control system or position servo control system can be composed of BLDM controller with computer or PLC through CAN communication interface or RS232 serial communication interface.By using the hardware in the loop simulation platform built by xPC target,the PI parameters are set up.The Speed servo response performance of the controller is tested.When the speed is 2 400 rpm,the response time of the controller is 0...
標簽：
stm32
無刷直流電機
上傳時間：
2022-05-07
上傳用戶：
