#include<iom16v.h> #include<macros.h> #define uint unsigned int #define uchar unsigned char uint a,b,c,d=0; void delay(c) { for for(a=0;a<c;a++) for(b=0;b<12;b++); }; uchar tab[]={ 0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,
上傳時間： 2013-10-21
上傳用戶：13788529953
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
標簽： Pulsoximeter Single-Chip Des
上傳時間： 2013-10-27
上傳用戶：黑漆漆
PCA9511, PCA9512, PCA9513, PCA9514, PCA9515, PCA9516, PCA9518,P82B96, P82B715Abstract - Philips Semiconductors family of Repeaters, Hubs and Expanders are detailed in this application notethat discusses device operation, maximum cable length and frequency calculations and typical applications.
上傳時間： 2013-11-21
上傳用戶：wlcaption
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上傳時間： 2014-04-02
上傳用戶：han_zh
Abstract: This application note explains the hardware of different types of 1-Wire® interfaces and software examples adapted to this hardware with a focus on serial ports. Depending on the types of iButtons required for a project and the type of computer to be used, the most economical interface is easily found. The hardware examples shown are basically two different types: 5V general interface and 12V RS-232 interface. Within the 5V group a common printed circuit board could be used for all circuits described. The variations can be achieved by different populations of components. The same principal is used for the 12V RS-232 interface. The population determines if it is a Read all or a Read/Write all type of interface. There are other possible circuit implementations to create a 1-Wire interface. The circuits described in this application note cover many different configurations. For a custom application, one of the described options can be adapted to meet individual needs.
標簽： iButtons Reading Writing and
上傳時間： 2013-10-29
上傳用戶：long14578
This application note describes how to retrieve user-defined data from Xilinx configurationPROMs (XC18V00 and Platform Flash devices) after the same PROM has configured theFPGA. The method to add user-defined data to the configuration PROM file is also discussed.The reference design described in this application note can be used in any of the followingXilinx FPGA architectures: Spartan™-II, Spartan-IIE, Spartan-3, Virtex™, Virtex-E, Virtex-II,and Virtex-II Pro.
上傳時間： 2013-11-11
上傳用戶：zhouli
摘要: 串行傳輸技術具有更高的傳輸速率和更低的設計成本, 已成為業界首選, 被廣泛應用于高速通信領域。提出了一種新的高速串行傳輸接口的設計方案, 改進了Aurora 協議數據幀格式定義的弊端, 并采用高速串行收發器Rocket I/O, 實現數據率為2.5 Gbps的高速串行傳輸。關鍵詞: 高速串行傳輸; Rocket I/O; Aurora 協議 為促使FPGA 芯片與串行傳輸技術更好地結合以滿足市場需求, Xilinx 公司適時推出了內嵌高速串行收發器RocketI/O 的Virtex II Pro 系列FPGA 和可升級的小型鏈路層協議———Aurora 協議。Rocket I/O支持從622 Mbps 至3.125 Gbps的全雙工傳輸速率, 還具有8 B/10 B 編解碼、時鐘生成及恢復等功能, 可以理想地適用于芯片之間或背板的高速串行數據傳輸。Aurora 協議是為專有上層協議或行業標準的上層協議提供透明接口的第一款串行互連協議, 可用于高速線性通路之間的點到點串行數據傳輸, 同時其可擴展的帶寬, 為系統設計人員提供了所需要的靈活性[4]。但該協議幀格式的定義存在弊端,會導致系統資源的浪費。本文提出的設計方案可以改進Aurora 協議的固有缺陷,提高系統性能, 實現數據率為2.5 Gbps 的高速串行傳輸, 具有良好的可行性和廣闊的應用前景。
上傳時間： 2013-11-06
上傳用戶：smallfish
Abstract: Communication with 1-Wire slave devices requires a 1-Wire master. There are numerous ways to build a 1-Wire master (see reference design 4206, "Choosing the Right 1-Wire Master for Embedded Applications"). Thisdocument describes the DS1WM, a synthesizable 1-Wire master that can be implemented in an application-specificintegrated circuit (ASIC) or field-programmable gate array (FPGA).
上傳時間： 2014-12-22
上傳用戶：xanxuan
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
上傳時間： 2013-10-23
上傳用戶：685
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
標簽： 無線技術
上傳時間： 2013-10-08
上傳用戶：kinochen
