I wrote this code early this year using ColdFire MCF5213 in codewarrior IDE. The LCD is STN B/W 320x240 dot matrix LCD. The code include 3 different fonts, and basic LCD driver. All original!
Data Structures and Algorithms
with Object-Oriented Design Patterns in Java
Bruno R. Preiss
B.A.Sc., M.A.Sc., Ph.D., P.Eng.
Associate Professor
Department of Electrical and Computer Engineering
University of Waterloo, Waterloo, Canada
隨著光伏發電系統快速發展,以及電動汽車充電樁的普及,傳統的剩余電流保護器無法滿足實際需求。介紹了一款B型剩余電流保護器,采用磁調制剩余電流互感器和零序電流互感器采集剩余電流。根據GB/T 22794—2017標準要求,可識別1 kHz及以下的正弦交流、帶和不帶直流分量的脈動直流、平滑直流等剩余電流信號。經信號調理電路將電壓信號送到單片機進行采集和判斷。通過試驗測試,該樣機在測試精度和速度上均符合國家標準的相關要求。The rapid development of photovoltaic power generation systems and the popularity of electric vehicle charging piles make the traditional residual current protective devices unable to meet the actual demand.This paper proposed a type B residual current protective device,which uses the magnetically modulated residual current transformer and the zero sequence current transformer to acquire the residual current.According to the requirements of GB/T 22794—2017,the type B residual current protective device can detect sinusoidal AC residual current of 1kHz and below 1kHz,pulsating DC residual current with and without DC component,smooth DC residual current and so on.The signal processing circuit sends the voltage signal to the MCU for acquisition and judgment.Through experimental tests,the device meets the relevant requirements of national standards in terms of test accuracy and speed.
針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。
Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
* "Copyright (c) 2006 Robert B. Reese ("AUTHOR")"
* All rights reserved.
* (R. Reese, reese@ece.msstate.edu, Mississippi State University)
* IN NO EVENT SHALL THE "AUTHOR" BE LIABLE TO ANY PARTY FOR
* DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT
* OF THE USE OF THIS SOFTWARE AND ITS DOCUMENTATION, EVEN IF THE "AUTHOR"
* HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Verilog HDL: Magnitude
For a vector (a,b), the magnitude representation is the following:
A common approach to implementing these arithmetic functions is to use the Coordinate Rotation Digital Computer (CORDIC) algorithm. The CORDIC algorithm calculates the trigonometric functions of sine, cosine, magnitude, and phase using an iterative process. It is made up of a series of micro-rotations of the vector by a set of predetermined constants, which are powers of two. Using binary arithmetic, this algorithm essentially replaces multipliers with shift and add operations. In a Stratix™ device, it is possible to calculate some of these arithmetic functions directly, without having to implement the CORDIC algorithm.
