This will sample all 8 A/D-channels by the continous mode. Each end of conversion will call an interrupt routine, where the AD-channel is put to Port4[2..0] and the upper nibble of the result is put to Port4[7..4]. Port 4 is connected to the user LEDs of the FlashCan100P Evaluation-Board
標簽： will D-channels conversion continous
上傳時間： 2013-12-09
上傳用戶：zm7516678
This example provides a description of how to set a communication with the bxCAN in loopback mode: - transmit and receive a standard data frame by polling at 100Kbit/S - transmit and receive an extended data frame with interrupt at 500Kbit/S - lit some LEDs depending of the program succeed or not
標簽： communication description provides loopback
上傳時間： 2016-04-24
上傳用戶：frank1234
This example provides a description of how to use a DMA channel to transfer a word data buffer from memory (Flash) to memory (RAM). The dedicated DMA channel is configured to transfer once a time a 32 word data buffer stored as constant in the Flash memory to another buffer in the RAM memory. The received data are stored in the DST_Buffer. The DMA channel transfer complete interrupt is enabled to generate an interrupt at the end of the buffer transfer. As soon as the transfer is completed an interrupt is generated and in the DMA channel interrupt routine the transfer complete interrupt pending bit is cleared. The data counter is stored before and after the transfer to show that all data has been transfered. TransferStatus gives the data transfer status where it is PASSED if transmitted and received data are the same otherwise it is FAILED
標簽： description provides transfer example
上傳時間： 2016-04-24
上傳用戶：ecooo
用STR710控制串口及CC1100進行無線通信，該開發工具為ARM公司的集成開發環境ADS，有完整的工程文件.mcp.
上傳時間： 2016-04-25
上傳用戶：陽光少年2016
基于s32410的GPS開發代碼。無操作系統，ADS開發。
標簽： s32410 GPS 代碼 無操作系統
上傳時間： 2014-10-12
上傳用戶：xjz632
基于LPC214X 的USB固件升級程序,通過USB接口來升級更新你的應用程序.基于LPC214X USB 固件升級源程序 (USB Firmware Upgrader source code ) 基于含有USB固件升級的LPC214X例程 例程包含下面編譯器的工程文件(Rowley CrossWorks Studio(GCC) 1.5, IAR ARM v.4.39, GCC 3.4 (4.10), ARM ADS 1.2, ARM RealView 2.2, Keil RVC v.3 )
上傳時間： 2016-04-28
上傳用戶：txfyddz
在arm下開發程序，使用keil或ads，此模板是周立功光盤里的資料，相當有參考價值
上傳時間： 2014-09-04
上傳用戶：zhaoq123
由三星的2442修改而來,正確引導eboot,請注意用三星公版的硬件配置,具體可以參考QQ2440,因為我在些平臺上跑過,具體操作 1.target settings : post-linker:選擇為 ARM fromELF 2.ARM assembler與 ARM c Compiler 的 architecture or processor 選擇為:ARM920T 3.ARM linker的 output:RO base為 0x00000000 (當仿真時為：0x30000000），layout的 object/sysmbol:為2440init.o section:Init 4.ARM fromELF 的 output:format:plain binary , output file name：nboot.bin 下面為全部源碼,注意用ADS編譯 2442addr.h 2442addr.inc 2442init.s 2442lib.c 2442lib.h 2442loader-1208.c 2442slib.h 2442slib.s Def.h k9s1208_s.s Memcfg.inc Nand.h Nand_mini.c Option.h Option.inc
標簽： post-linker settings target eboot
上傳時間： 2016-05-06
上傳用戶：moshushi0009
s3c2440的dma操作控制程序，在ADS環境編譯，運行
上傳時間： 2016-05-06
上傳用戶：libinxny
s3c2440的液晶屏操作控制程序（SHARP/SAMSUNG都可以），在ADS環境編譯，運行
標簽： s3c2440 SAMSUNG SHARP 液晶屏
上傳時間： 2014-11-27
上傳用戶：wyc199288
蟲蟲下載站版權所有 京ICP備2021023401號-1
