This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上傳時間： 2013-11-02
上傳用戶：zw380105939
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
上傳時間： 2013-10-21
上傳用戶：xiaozhiqban
當拿到一張CASE單時，首先得確定的是能用什么母體才能實現此功能，然后才能展開對外圍硬件電路的設計，因此首先得了解每個母體的基本功能及特點，下面大至的介紹一下本公司常用的IC：單芯片解決方案• SN8P1900 系列– 高精度 16-Bit 模數轉換器– 可編程運算放大器 (PGIA)• 信號放大低漂移: 2V• 放大倍數可編程: 1/16/64/128 倍– 升壓- 穩壓調節器 (Charge-Pump Regulator)• 電源輸入: 2.4V ~ 5V• 穩壓輸出: e.g. 3.8V at SN8P1909– 內置液晶驅動電路 (LCD Driver)– 單芯片解決方案 • 耳溫槍 SN8P1909 LQFP 80 Pins• 5000 解析度量測器 SN8P1908 LQFP 64 Pins• 體重計 SN8P1907 SSOP 48 Pins單芯片解決方案• SN8P1820 系列– 精確的12-Bit 模數轉換器– 可編程運算放大器 (PGIA)• Gain Stage One: Low Offset 5V, Gain: 16/32/64/128• Gain Stage One: Low Offset 2mV, Gain: 1.3 ~ 2.5– 升壓- 穩壓調節器• 電源輸入: 2.4V ~ 5V• 穩壓輸出: e.g. 3.8V at SN8P1829– 內置可編程運算放大電路– 內置液晶驅動電路 – 單芯片解決方案 • 電子醫療器 SN8P1829 LQFP 80 Pins 高速/低功耗/高可靠性微控制器• 最新SN8P2000 系列– SN8P2500/2600/2700 系列– 高度抗交流雜訊能力• 標準瞬間電壓脈沖群測試 (EFT): IEC 1000-4-4• 雜訊直接灌入芯片電源輸入端• 只需添加1顆 2.2F/50V 旁路電容• 測試指標穩超 4000V (歐規)– 高可靠性復位電路保證系統正常運行• 支持外部復位和內部上電復位• 內置1.8V 低電壓偵測可靠復位電路• 內置看門狗計時器保證程序跳飛可靠復位– 高抗靜電/栓鎖效應能力– 芯片工作溫度有所提高: -200C ~ 700C 工規芯片溫度： -400C ~ 850C 高速/低功耗/高可靠性微控制器• 最新 SN8P2000 系列– SN8P2500/2600/2700 系列– 1T 精簡指令級結構• 1T: 一個外部振蕩周期執行一條指令• 工作速度可達16 MIPS / 16 MHz Crystal– 工作消耗電流 < 2mA at 1-MIPS/5V– 睡眠模式下消耗電流 < 1A / 5V額外功能• 高速脈寬調制輸出 (PWM)– 8-Bit PWM up to 23 KHz at 12 MHz System Clock– 6-Bit PWM up to 93 KHz at 12 MHz System Clock– 4-Bit PWM up to 375 KHz at 12 MHz System Clock• 內置高速16 MHz RC振蕩器 (SN8P2501A)• 電壓變化喚醒功能• 可編程控制沿觸發/中斷功能– 上升沿 / 下降沿 / 雙沿觸發• 串行編程接口
上傳時間： 2013-10-21
上傳用戶：jiahao131
Abstract: Designers who must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
標簽： PicoBlaze Create Master Xilinx
上傳時間： 2013-11-05
上傳用戶：a6697238
a8259 可編程中斷控制 altera提供 The a8259 is designed to simplify the implementation of the interrupt interface in 8088 and 8086 based microcomputer systems. The device is known as a programmable interrupt controller. The a8259 receives and prioritizes up to 8 interrupts, and in the cascade mode, this can be expanded up to 64 interrupts. An asynchronous reset and a clock input have been added to improve operation and reliability.
上傳時間： 2014-11-29
上傳用戶：zhyiroy
多遠程二極管溫度傳感器-Design Considerations for pc thermal management Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
標簽： Considerat Design 遠程 二極管
上傳時間： 2014-12-21
上傳用戶：ljd123456
The C8051F020/1/2/3 devices are fully integrated mixed-signal System-on-a-Chip MCUs with 64 digital I/O pins (C8051F020/2) or 32 digital I/O pins (C8051F021/3). Highlighted features are listed below; refer to Table 1.1 for specific product feature selection.
上傳時間： 2013-11-08
上傳用戶：lwq11
針對UHF讀寫器設計中，在符合EPC Gen2標準的情況下，對標簽返回的高速數據進行正確解碼以達到正確讀取標簽的要求，提出了一種新的在ARM平臺下采用邊沿捕獲統計定時器數判斷數據的方法，并對FM0編碼進行解碼。與傳統的使用定時器定時采樣高低電平的FM0解碼方法相比，該解碼方法可以減少定時器定時誤差累積的影響；可以將捕獲定時器數中斷與數據判斷解碼相對分隔開，使得中斷對解碼影響很小，實現捕獲與解碼的同步。通過實驗表明，這種方法提高了解碼的效率，在160 Kb/s的接收速度下，讀取一張標簽的時間約為30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上傳時間： 2013-11-10
上傳用戶：liufei
This example shows how to update at regulate period the WWDG counter using theEarly Wakeup interrupt (EWI). The WWDG timeout is set to 262ms, refresh window set to 41h and the EWI isenabled. When the WWDG counter reaches 40h the EWI is generated and in the WWDGISR the counter is refreshed to prevent a WWDG reset and led connected to PC.07is toggled.The EXTI line9 is connected to PB.09 pin and configured to generate an interrupton falling edge.In the NVIC, EXTI line9 to 5 interrupt vector is enabled with priority equal to 0and the WWDG interrupt vector is enabled with priority equal to 1 (EXTI IT > WWDG IT). The EXTI Line9 will be used to simulate a software failure: once the EXTI line9event occurs (by pressing Key push-button on EVAL board) the correspondent interruptis served, in the ISR the led connected to PC.07 is turned off and the EXTI line9pending bit is not cleared. So the CPU will execute indefinitely EXTI line9 ISR andthe WWDG ISR will never be entered(WWDG counter not updated). As result, when theWWDG counter falls to 3Fh the WWDG reset occurs.If the EXTI line9 event don抰 occurs the WWDG counter is indefinitely refreshed inthe WWDG ISR which prevent from WWDG reset. If the WWDG reset is generated, after resuming from reset a led connected to PC.06is turned on. In this example the system is clocked by the HSE(8MHz).
上傳時間： 2013-11-11
上傳用戶：gundamwzc
#include <reg51.h>#include <main.h>#include <interrupt.h> cs5460a應用電路(含源程序)bit code table_odd_even_bit[16]={0,1,1,0,1,0,0,1,1,0,0,1,0,1,1,0}; extern uchar rs485_timeout,pointer_buf485;extern uchar rs485_buf[MAX_485_LEN];extern uchar idata spi_buf[MAX_SPI_LEN];extern uchar pointer_send,send_len; extern uchar count_1s;//extern uint count_2min;extern uint count_10s;extern uchar oper_len,send_offset,chk_sum,send_i;extern bit flag_send_data,flag_level,flag_drdy,flag_data_ok;
上傳時間： 2014-01-24
上傳用戶：heart_2007
