MPLAB C30用戶指南(英文)
HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support
Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use Interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an Interruptservice Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating Interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR Interrupts, as these featuresare already designed into the device.
a8259 可編程中斷控制 altera提供
The a8259 is designed to simplify the implementation of the interrupt interface in 8088 and 8086 based microcomputer systems. The device is known as a programmable interrupt controller. The a8259 receives and prioritizes up to 8 Interrupts, and in the cascade mode, this can be expanded up to 64 Interrupts. An asynchronous reset and a clock input have been added to improve operation and reliability.
a8259 可編程中斷控制 altera提供
The a8259 is designed to simplify the implementation of the interrupt interface in 8088 and 8086 based microcomputer systems. The device is known as a programmable interrupt controller. The a8259 receives and prioritizes up to 8 Interrupts, and in the cascade mode, this can be expanded up to 64 Interrupts. An asynchronous reset and a clock input have been added to improve operation and reliability.
This firmware translates a PS/2 mouse to a USB mouse. The translator
firmware is entirely interrupt driven (with the exception of sending the
data via USB to the host.) An interrupt is generated when the PS/2 start
bit is received, at which time the firmware will begin its receive routine.
In addition to this interrupt, every 168ms a timer overflow Interrupts the
main program and implements one state of the mouse state machine. This
state machine handles sending bytes to and translating bytes received from
the PS/2 mouse automatically. All of this is done in the background while
the main program runs in the foreground. The only operation that the main
program implements is sending mouse data to the PC via USB.
Details for How to develop an OAL .Step-by-step to develop an OAL. An OEM adaptation layer (OAL) is a layer of code between the Windows CE kernel and the hardware of your target device. You develop an OAL to communicate data between your operating system (OS) and your target device and include code to handle Interrupts, timers, and so on.
VDSP++打開。This directory contains an example ADSP-BF537 RTC project that does a basic blink routine and
then puts the part in deep sleep mode to be woken up from a RTC Stopwatch Event. Once woken up,
the RTC is reconfigured to toggle the EZ KIT LEDs using RTC second, minute, hour, and day Interrupts.
