The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
The power appetite of large TFT-LCDs appears to beinsatiable. Power supplies must feed increasing numbersof transistors and improved display resolutions, and doso without taking much space.
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
The voltage range of Linear Technology’s PowerPath® circuitscan be easily extended with just a few components, thusallowing them to meet the needs of virtually all applications.This application note presents solutions for circuits thatmust withstand large negative voltages, a reverse adapterinput for example, and circuits that must withstand largepositive inputs, such as automotive load-dump.
A large group of fiber optic lasers are powered by DCcurrent. Laser drive is supplied by a current source withmodulation added further along the signal path. Thecurrent source, although conceptually simple, constitutesan extraordinarily tricky design problem. There are anumber of practical requirements for a fiber optic currentsource and failure to consider them can cause laser and/or optical component destruction.
The LTM4601 DC/DC μModule regulator is a completehigh power density stepdown regulator for up to 12Acontinuous (14A peak) loads. The device is housed ina small 15mm ¥ 15mm ¥ 2.8mm LGA surface mountpackage, thus the large power dissipation is a challengein some applications. This thermal application note willprovide guidelines for using the μModule regulator inambient environments with or without air fl ow. Loadcurrent derating curves are provided for several inputvoltages and output voltages versus ambient temperatureand air fl ow.
現有基于MAX7219芯片的數碼管驅動電路只適用于小尺寸LED，為擴展其使用范圍，在介紹動態顯示芯片MAX7219功能的基礎上，提出了一個基于該芯片的8位高亮度8英寸數碼管驅動電路。電路保留了MAX7219芯片的功能強大、編程簡單等優點，通過74LS273鎖存器和ULN2803達林頓驅動器，實現了對任意大尺寸數碼管提供較高電壓和電流驅動的靜態顯示，并亮度可調。
Abstract:
The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with higher voltage and current was achieved with the help of 74LS273 and ULN2803.
AVR32801: UC3A3 Schematic Checklist Features • Power circuit • Reset circuit • USB connection • External bus interface • ABDAC sound DAC interface • JTAG and Nexus debug ports • Clocks and crystal oscillators • MMC, SD-card, SDHC, SDIO and CE-ATA interface 1 Introduction A good hardware design comes from a proper schematic. Since UC3A3 devices have a fair number of pins and functions, the schematic for these devices can be large and quite complex. This application note describes a common checklist which should be used when starting and reviewing the schematics for a UC3A3 design.
