<center id="eoy0k"></center> <center id="eoy0k"></center> There is an unprecedented enthusiasm for radio frequency identification (RFID) technologies today. RFID is based on the exchange of information carried by electromagnetic waves between a Label, or tag, and a reader. This technology is currently in full economic expansion, which has manifested itself in widely backed research activities, some of which will be examined in this book.
標簽： Identification Frequency Sensors Radio and
上傳時間： 2020-06-08
上傳用戶：shancjb
Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product Label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
標簽： agilent
上傳時間： 2022-02-20
上傳用戶：
1.bus indices out of range 總線分支索引超出范圍2.Bus range syntax errors 總線范圍的語法錯誤3.Illegal bus range values 非法的總線范圍值4.Illegal bus definitions 定義的總線非法5.Mismatched bus Label ordering 總線分支網絡標號錯誤排序6.Mismatched bus/wire object on wire/bus 總線/導線錯誤的連接導線/總線
標簽： Altium Designer
上傳時間： 2022-04-17
上傳用戶：qdxqdxqdxqdx
第一步：新建PCB工程文件 并向工程文件里添加PCB文件和原理圖文件 第二步：元件庫、封裝庫設計 部分元器件廠商或者經銷商不提供元件庫和封裝庫，只給了元器件尺寸圖，所以需要自行設計元件 庫文件或是封裝庫文件 元件庫設計： 新建 .SchLib 文件：File -> New -> Library -> Schematic Library 使用Place下拉菜單或使用快捷工具欄放置圖形，引腳等，記得保存！ 封裝庫的設計 新建.PcbLib文件：File -> New -> Library -> PCB Library 使用Place下拉菜單或使用快捷工具欄，畫線，放置孔位，記得保存！第三步：原理圖的繪制 新建.SchDoc文件 ：File -> New -> Schematic 添加元器件庫和封裝庫 在軟件底部菜單欄System中勾選Libraries，打開側面工具欄 在側面工具欄中點擊“Libraries...” -> “Add Library”找到自己保存的庫文件并添加 添加各元器件 可直接從側面工具欄中選擇元器件拖入原理圖中，在拖動過程中按Tab鍵修改元器件信息 添加網絡標識Place -> Net Label 快捷鍵（PN） 確定各元器件封裝 打開封裝管理器Tools -> Footprint Manager 快捷鍵（TG） 可挨個修改、檢查各元器件封裝
標簽： altium designer pcb
上傳時間： 2022-07-23
上傳用戶：
