Photodiodes can be broken into two categories: Largearea photodiodes with their attendant high capacitance(30pF to 3000pF) and smaller area photodiodes withrelatively low capacitance (10pF or less). For optimalsignal-to-noise performance, a transimpedance amplifi erconsisting of an inverting op amp and a feedback resistoris most commonly used to convert the photodiode currentinto voltage. In low noise amplifi er design, Large areaphotodiode amplifi ers require more attention to reducingop amp input voltage noise, while small area photodiodeamplifi ers require more attention to reducing op amp inputcurrent noise and parasitic capacitances.
One of the most critical components in a step-up design like Figure 1 is the transformer. Transformers have parasitic components that can cause them to deviate from their ideal characteristics, and the parasitic capacitance associated with the secondary can cause Large resonating current spikes on the leading edge of the switch current waveform.
Power conversion by virtue of its basic role produces harmonics due to theslicing of either voltages or currents. To a Large extent the pollution in theutility supply and the deterioration of the power quality has been generatedor created by non-linear converters. It is therefore ironic that power convertersshould now be used to clean up the pollution that they helped to create inthe first place.In a utility system, it is desirable to prevent harmonic currents (which resultin EMI and resonance problems) and limit reactive power flows (whichresult in transmission losses).Traditionally, shunt passive filters, comprised of tuned LC elements andcapacitor banks, were used to filter the harmonics and to compensate forreactive current due to non-linear loads. However, in practical applicationsthese methods have many disadvantages.
The LTP5900 includes sufficient power supply filtering and decoupling capacitancesuch that additional filtering should not be necessary for most battery-powereddesigns. Care must be taken to avoid Large transient voltages on the supply as theM2510 steps up its current consumption (see the section on Supply Design below).
Abstract: With its small size and Large load (10W) capability, the MAX13256 H-bridge transformer driver is an attractive solution forcharging supercapacitors (supercaps). However, a Large capacitance on the output of the circuit can force the driver into fault modeat startup, due to the high initial charge current. This application note presents a solution that allows users to charge a Largecapacitance without going into fault.
The LT®1943 is a highly integrated, 4-output regulatordesigned to power Large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a Large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
The power appetite of Large TFT-LCDs appears to beinsatiable. Power supplies must feed increasing numbersof transistors and improved display resolutions, and doso without taking much space.
