-
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
標簽：
DC
降壓
升壓型
控制器
上傳時間：
2013-10-21
上傳用戶：ljt101007
-
The LTC®3562 quad output step-down regulator is designedfor multicore handheld microprocessor applications thatoperate from a single Li-Ion battery. Its four monolithic, higheffi ciency buck regulators support Intel’s mobile CPU P-Stateand C-State energy saving operating modes. The outputvoltages are independently controllable via I2C, and eachoutput can be independently started and shut down. Designerscan choose from power saving pulse-skipping mode orBurst Mode® operation, or select low noise LDO mode. Thespace-saving LTC3562 is available in a 3mm × 3mm QFNpackage and requires few external components.
標簽：
DC
442
I2C
DN
上傳時間：
2013-10-07
上傳用戶：1583060504
-
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
標簽：
436
DN
全橋
壓電
上傳時間：
2013-11-18
上傳用戶：hulee
-
Automotive power systems are unforgiving electronicenvironments. Transients to 90V can occur when thenominal voltage range is 10V to 15V (ISO7637), along withbattery reversal in some cases. It’s fairly straightforwardto build automotive electronics around this system, butincreasingly end users want to operate portable electronics,such as GPS systems or music/video players,and to charge their Li-Ion batteries from the automotivebattery. To do so requires a compact, robust, effi cientand easy-to-design charging system
標簽：
464
USB
DN
高效率
上傳時間：
2013-11-04
上傳用戶：wfl_yy
-
The LTC®4155 and LTC4156 are dual multiplexed-inputbattery chargers with PowerPath™ control, featuring I2Cprogrammability and USB On-The-Go for systems suchas tablet PCs and other high power density applications.The LTC4155’s float voltage (VFLOAT) range is optimizedfor Li-Ion batteries, while the LTC4156 is optimized forlithium iron phosphate (LiFePO4)batteries, supportingsystem loads to 4A with up to 3.5A of battery chargecurrent. I2C controls a broad range of functions and USBOn-The-Go functionality is controlled directly from theUSB connector ID pin.
標簽：
高電流
便攜式產品
電池充電器
方案
上傳時間：
2013-10-09
上傳用戶：hanhanj
-
The NXP LPC315x combine an 180 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, an integratedaudio codec, Li-Ion charger, Real-Time Clock (RTC), and a myriad of serial and parallelinterfaces in a single chip targeted at consumer, industrial, medical, and communicationmarkets. To optimize system power consumption, the LPC315x have multiple powerdomains and a very flexible Clock Generation Unit (CGU) that provides dynamic clockgating and scaling.The LPC315x is implemented as multi-chip module with two side-by-side dies, one fordigital fuctions and one for analog functions, which include a Power Supply Unit (PSU),audio codec, RTC, and Li-Ion battery charger.
標簽：
315x
LPC
315
ARM
上傳時間：
2014-01-17
上傳用戶：Altman
-
The PW4556 series of devices are highly integrated Li-Ion and Li-Pol linear chargers targetedat small capacity battery for portable applications. It is a complete constant-current/ constantvoltage linear charger. No external sense resistor is needed, and no blocking diode is required dueto the internal MOSFET architecture. It can deliver up to 300mA of charge current (using a goodthermal PCB layout) with a final float voltage accuracy of ±1%. The charge voltage is fixed at 4.2V or4.35V, and the charge current can be programmed externally with a single resistor. The chargerfunction has high accuracy current and voltage regulation loops and charge termination
標簽：
pw4556
上傳時間：
2022-02-11
上傳用戶：1208020161
-
The PW4554 is a cost-effective, fully integrated high input voltage single-cell Li-Ion battery charger.The charger uses a CC/CV charge profile required by Li-Ion battery. The charger accepts an inputvoltage up to 24V but is disabled when the input voltage exceeds the OVP threshold, typically 6.8V,to prevent excessive power dissipation. The 24V rating eliminates the over-voltage protection circuitrequired in a low input voltage charger
標簽：
pw4554
上傳時間：
2022-02-11
上傳用戶：
-
PW4203 is a 4.5-22V input, 2A multi-cell synchronous Buck Li-Ion battery charger, suitable forportable application. Select pin is convenient for multi-cell charging. 800 kHz synchronous buckregulator integrates of 22V rating FETs with ultra low on- resistance to achieve high efficiency andsimple circuit design.The PW4203 is available in an 8-pin SOP package, provides a very compact system solution andgood thermal conductance
標簽：
pw4203
上傳時間：
2022-02-11
上傳用戶：
-
The PW3130 series product is a high integration solution for lithium-lion/polymer batteryprotection.PW3130 contains advanced power MOSFET, high-accuracy voltage detection circuits anddelay circuits. PW3130 is put into an ultra-small SOT23-5 package and only one external componentmakes it an ideal solution in limited space of battery pack. PW3130 has all the protection functionsrequired in the battery application including overcharging, overdischarging, overcurrent and loadshort circuiting protection etc. The accurate overcharging detection voltage ensures safe and fullutilization charging.The low standby current drains little current from the cell while in storage. Thedevice is not only targeted for digital cellular phones, but also for any other Li-Ion and Li-Polybattery-powered information appliances requiring long-term battery life
標簽：
pw3130
上傳時間：
2022-02-11
上傳用戶：fliang
