針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上傳時間： 2013-10-10
上傳用戶：asdfasdfd
Chipcon CC2420 reference design w/PA board rev B CC2420_w_PA_PCB.ZIP FABRICATION.PHO - fabrication drawing COPPER1.PHO - copper layer #1 (top side) COPPER2.PHO - copper layer #2 (inner ground plane) COPPER3.PHO - copper layer #3 (inner power plane) COPPER4.PHO - copper layer #4 (bottom side) TOPMASK.PHO - top side solder mask BOTTOMMASK.PHO - bottom side solder mask NCDRILL.DRL - drill data file NCDRILL.LST - drill list NCDRILL.REP - drill report
標簽： 2420 FABRICATION reference fabricati
上傳時間： 2015-05-12
上傳用戶：xc216
DESCRIPTION : BIN to seven segments converter -- segment encoding -- a -- +---+ -- f | | b -- +---+ <- g -- e | | c -- +---+ -- d -- Enable (EN) active : high -- Outputs (data_out) active : low
標簽： DESCRIPTION converter segments encoding
上傳時間： 2016-08-17
上傳用戶：ainimao
隨著光伏發電系統快速發展,以及電動汽車充電樁的普及,傳統的剩余電流保護器無法滿足實際需求。介紹了一款B型剩余電流保護器,采用磁調制剩余電流互感器和零序電流互感器采集剩余電流。根據GB/T 22794—2017標準要求,可識別1 kHz及以下的正弦交流、帶和不帶直流分量的脈動直流、平滑直流等剩余電流信號。經信號調理電路將電壓信號送到單片機進行采集和判斷。通過試驗測試,該樣機在測試精度和速度上均符合國家標準的相關要求。The rapid development of photovoltaic power generation systems and the popularity of electric vehicle charging piles make the traditional residual current protective devices unable to meet the actual demand.This paper proposed a type B residual current protective device,which uses the magnetically modulated residual current transformer and the zero sequence current transformer to acquire the residual current.According to the requirements of GB/T 22794—2017,the type B residual current protective device can detect sinusoidal AC residual current of 1kHz and below 1kHz,pulsating DC residual current with and without DC component,smooth DC residual current and so on.The signal processing circuit sends the voltage signal to the MCU for acquisition and judgment.Through experimental tests,the device meets the relevant requirements of national standards in terms of test accuracy and speed.
標簽： 電流保護器
上傳時間： 2022-03-27
上傳用戶：
21世紀大學新型參考教材系列 集成電路B 荒井
上傳時間： 2013-04-15
上傳用戶：eeworm
家電維修(最基礎的教程B)1-20.Torrent
上傳時間： 2013-06-10
上傳用戶：eeworm
jk-b交通信號控制機原理圖
上傳時間： 2013-07-13
上傳用戶：eeworm
專輯類-實用電子技術專輯-385冊-3.609G jk-b交通信號控制機原理圖-1.3M.zip
上傳時間： 2013-08-02
上傳用戶：zhf1234
專輯類-電子基礎類專輯-153冊-2.20G 21世紀大學新型參考教材系列-集成電路B-荒井-159頁-2.8M.pdf
上傳時間： 2013-05-16
上傳用戶：pkkkkp
三次B樣條曲線源代碼,C語言編寫的三次B樣條曲線源代碼，希望大家喜歡。
標簽：
上傳時間： 2013-07-13
上傳用戶：chengli008
蟲蟲下載站版權所有 京ICP備2021023401號-1
