The STi7105 uses state of the art process
technology to provide an ultra low-cost, fully
featured HD AVC decoder IC. It is a highly
integrated system-on-chip suitable for STB markets across all networks (cable/satellite/DTT/x-
DSL/IP) worldwide
12bit 低功耗DAC 數模轉換器
The MAX5302 combines a low-power, voltage-output,
12-bit digital-to-analog converter (DAC) and a precision
output amplifier in an 8-pin μMAX package. It operates
from a single +5V supply, drawing less than 280μA of
supply current.
The AP2406 is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. It is ideal for powering portable equipment that runs from a single cell lithium-Ion (Li+) battery. The AP2406 can supply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The AP2406 can also run at 100% duty cycle for low dropout operation, extending battery life in portable system. Idle mode operation at light loads provides very low output ripple voltage for noise sensitive applications.
The AP2406 is offered in a low profile (1mm) 5-pin, thin SOT package, and is available in an adjustable version and fixed output voltage of 1.2V, 1.5V and 1.8V
The SP2526A device is a dual +3.0V to +5.5V USB Supervisory Power Control Switch ideal
for self-powered and bus-powered Universal Serial Bus (USB) applications. Each switch has
low on-resistance (110mΩ typical) and can supply 500mA minimum. The fault currents are
limited to 1.0A typical and the flag output pin for each switch is available to indicate fault
conditions to the USB controller. The thermal shutdown feature will prevent damage to the
device when subjected to excessive current loads. The undervoltage lockout feature will
ensure that the device will remain off unless there is a valid input voltage present.
PW4203 is a 4.5-22V input, 2A multi-cell synchronous Buck Li-Ion battery charger, suitable forportable application. Select pin is convenient for multi-cell charging. 800 kHz synchronous buckregulator integrates of 22V rating FETs with ultra low on- resistance to achieve high efficiency andsimple circuit design.The PW4203 is available in an 8-pin SOP package, provides a very compact system solution andgood thermal conductance
The PW4055 is a complete constant-current /constant-voltage linear charger for single cell lithiumion batteries.Its ThinSOT package and low external component count make the PW4055 ideallysuited for portable applications.Furthermore, the PW4055 is specifically designed to work within USBpower specifications.The PW4055 No external sense resistor is needed, and no blocking diode is required due to theinternal MOSFET architecture.Thermal feedback regulates the charge current to limit the dietemperature during high power operation or high ambient temperature. The charge voltage is fixedat 4.2V, and the charge current can be programmed externally with a single resistor. The PW4055automatically terminates the charge cycle when the charge current drops to 1/10th the programmedvalue after the final float voltage is reached. When the input supply (wall adapter or USB supply) isremoved, the PW4055 automatically enters a low current state, dropping the battery drain currentto less than 2μA. The PW4055 can be put into shutdown mode, reducing the supply current to 25μA.The BAT pin has a 7KV ESD(HBM) capability. Other features include charge current monitor, undervoltage lockout, automatic recharge and a status pin to indicate charge termination and the presenceof an input voltage
本文首次設計并驗證了基于macom三合一芯片設計的光模塊電路,該電路旨在提供一種滿足SFF-8472中規定的數字診斷功能的低成本SFP+模塊。電路采用激光器驅動、限幅放大器、控制器以及時鐘恢復單元集成的單芯片,在保證高精度數字診斷功能基礎上,實現了低成本高可靠的特點。該電路在光接收接口組件與激光器驅動和限幅放大器單元的限幅放大器部分之間接入濾波器來提高模塊的靈敏度及信號質量。在控制器單元的數字電位器的引腳上采用外加電阻的方式避免出現上電不發光的故障問題。該研究結果為下一代SFP-DD光模塊設計與開發工作,奠定了一定的理論與實踐基礎。This paper designs and validates the optical module circuit based on the MACOM Trinity chip for the first time.This circuit aims to provide a low-cost SFP module which meets the digital diagnosis function specified in SFF-8472.The circuit uses a single chip integrated with laser driver,limiting amplifier,controller and clock recovery unit.On the basis of ensuring high precision digital diagnosis function,it achieves the characteristics of low cost and high reliability.The circuit connects a filter between the optical receiving interface module and the limiting amplifier part of the laser driver and limiting amplifier unit to improve the sensitivity and signal quality of the module.The pin of the digital potentiometer in the controller unit is equipped with an external resistance to avoid the problem of power failure.The research results lay a theoretical and practical foundation for optical module design in high-speed data center.
