Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "MONITORing and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
標簽： agilent
上傳時間： 2022-02-20
上傳用戶：
設計了農業溫濕度智能控制系統,該系統采用DHT11溫濕度傳感器作為溫濕度采集模塊,單片機選用AT89C52代替并調用Virtual terminal模擬串口通信,LCD1604液晶顯示器實時顯示溫濕度,實現了溫濕度的測量、顯示,可自動控制加熱、降溫、加濕、通風,實現溫濕度控制以及超限報警處理,并利用Proteus與Keil進行實際電路的仿真。試驗表明,該系統實現了可靠的溫濕度監控。We described the design of an intelligent control system of agriculture temperature and humidity.The system uses DHT11 temperature and humidity sensor as the temperature and humidity acquisition module.The SCM adopts AT89C52 to replace and call the virtual terminal for simulating serial communication.LCD1604 displays temperature and humidity in real time,which implements the measurement and display of temperature and humidity.The system is able to automatically control heating,cooling,humidification and ventilation,to achieve temperature and humidity control and over-limit alarm processing.The system also uses Proteus and Keil for actual circuit simulation.The experiment shows that the system is capable of reliable temperature and humidity MONITORing.
上傳時間： 2022-03-26
上傳用戶：aben
近年來反季節種植已成火熱趨勢,溫室大棚的普及十分迅速,而溫室大棚對自動化、智能化的要求也越來越迫切,本系統將溫室大棚的溫濕度、二氧化碳濃度各個方面的檢測,通風、澆灌、溫度、噴灑農藥等各個方面的控制進行綜合系統研究,實現溫室大棚對自動化、智能化的要求。這一系統是基于單片機控制的智能檢測,控制系統包含單片機主控模塊、感應檢測模塊、傳感模塊,顯示、控制模塊等[1]。從而提高溫室大棚的種植效率,減少勞動力,提高利潤等。In recent years,counter-season planting has become a hot trend featuring the rapid popularization of greenhouse and urgent requirement for the automation and intellectualization of greenhouse.This paper offers a comprehensive and systematic study of the MONITORing of temperature,humidity and carbon dioxide concentration in the greenhouse and the control of ventilation,irrigation,temperature and pesticide spraying in order to achieve automation and intellectualization in greenhouse.This system is based on the intelligent detection controlled by single chip computer with the control system including the main control module,induction detection module,sensing module,display and control module of single chip computer,which is effective in improving planting efficiency of greenhouse,reducing labor force and increasing profits.
上傳時間： 2022-03-27
上傳用戶：
設計了自動控制系統綜合實驗案例“基于LabVIEW和單片機的溫度控制系統設計”。實驗系統硬件部分由單片機、溫度傳感器、D/A轉換模塊、調壓模塊和電烤箱組成,設計了單片機與各個模塊之間的接口電路。軟件部分采用LabVIEW軟件實現控制算法,并設計監控界面實現參數設定、溫度數據實時監控等功能。設計了單片機與LabVIEW軟件之間的串口通信程序,實現了輸入、輸出數據的傳輸。通過綜合實驗系統設計,使學生得到控制系統設計和實驗調試等綜合能力的訓練。A comprehensive experimental case of the automatic control system is presented,which is the design of the temperature control system based on LabVIEW and SCM.The hardware part of the experimental system is composed of the SCM,temperature sensor,D/A conversion module,voltage regulating module and electric oven.The interface circuit between the SCM and each module is designed.In the software part,LabVIEW software is used to realize the control algorithm,and the MONITORing interface is designed to realize the functions of parameter setting,temperature data real-time MONITORing,etc.The serial communication program between the SCM and LabVIEW software is designed to realize the transmission of input and output data.Through the design of this comprehensive experimental system,students can get the comprehensive ability training for the control system design,experiment debugging,etc.
上傳時間： 2022-03-27
上傳用戶：qdxqdxqdxqdx
鋰電池BMS管理技術是移動機器人的關鍵技術,本文設計了基于bq76PL455、STM32F103的鋰電池管理系統,實現了電池組電壓、電流、過壓、過流等狀態監測;系統配置均衡電路,電池充電過程中若出現電池單體電壓不平衡現象,會觸發均衡電路,進而提高電池的安全性,延長使用壽命。Lithium battery BMS management technology is the key technology of mobile robot.The lithium battery management system based on bq76PL455 and STM32F103 is proposed to realize the MONITORing of battery pack voltage,current,overvoltage and overcurrent.The system is equipped with equalization circuit.When the battery cell voltage imbalance occurs,the equalization circuit is triggered to improve the safety and service life of the battery.
上傳時間： 2022-04-02
上傳用戶：
在全球氣候變暖和石油資源短缺的形勢下,推動新能源汽車的發展將成為汽車行業一種新的發展方向。在大力發展新能源電動汽車行業的同時還應兼顧電動汽車充電設施的發展,因此對電動汽車充電樁的設計與研究顯得十分必要。對電動汽車直流充電樁的硬件系統進行設計,主要的硬件電路包括安全監測電路、總壓采集電路、溫濕度檢測電路、語音電路。軟件包括主要流程圖和溫濕度檢測流程圖。Under the situation of global warming and shortage of petroleum resources,promoting the development of new energy vehicles will become a new development direction for the automotive industry.While vigorously developing the new energy electric vehicle industry,we should also take into account the development of electric vehicle charging facilities.Therefore,the design and research of electric vehicle charging piles is very necessary.The hardware system of the electric vehicle DC charging pile is designed.The main hardware circuits include safety MONITORing circuit,total voltage collecting circuit,temperature and humidity detecting circuit,voice circuit and CAN communication.The software includes a main flow chart and a temperature and humidity detection flow chart.
標簽： 電動汽車
上傳時間： 2022-04-03
上傳用戶：jason_vip1
為適應雙向DC/DC功率變換的電流采樣需求,一種高精度高邊電流采樣電路被提出。其基本思想是在功率電路的高邊串入采樣電阻,借助電流鏡原理并引入偏置電流電路,將雙向電流均轉換為正向電壓輸出。通過理論分析與仿真結合的方法對電流鏡采樣原理及4種不同的偏置電流電路方案進行對比,最后通過實驗數據驗證了高精度高邊電流采樣電路的有效性。實驗數據表明,該采樣電路可在-25~75℃的溫度工作范圍內,針對-10~＋10 A范圍內的電流采樣實現優于5%的采樣精度。Current sensing plays an important role in controlling,MONITORing or protection functions of power systems.To meet the current sensing requirement of bidirectional DC/DC converters,a high-accuracy bidirectional current sensing circuit is proposed.The proposed current sensing circuit inserts a resistor in the path of the current to be sensed,while the current mirror and biased current circuit are introduced.Therefore,the bidirectional current can be expressed by positive voltage.By theoretical analysis and simulation,the sampling theory is analyzed and four biased current circuits are compared.At last,experimental results verified the proposed method.It is demonstrated that the proposed current sensing circuit can achi...
上傳時間： 2022-04-22
上傳用戶：
隨著汽車行業的飛速發展，汽車市場的不斷升溫，與之相關的電子技術也得到時了迅速發展及廣泛應用，汽車技術的成熟使得汽車銷售及使用不斷壯大，現代汽車的行駛速度也隨著路況的提高，汽車性能的提高而不斷提升。而由于突發性道路交通事故的頻繁發生，人們對汽車安全的關注度也日益提高。在汽車的高速行駛過程中，輪胎故障是駕駛人員最為擔心和最難預防的，也是突發性交通事故發生的重要原因。據統計，在高速公路上發生的交通事故有70%-80%是由于爆胎引起的，怎樣防止爆胎已成為汽車安全的第一大重要課題。權威的研究結果表明，保持標準的輪胎氣壓和及時發現輪胎故障是防止爆胎的關鍵，這就使對輪胎充氣壓力實行監測顯得非常重要。本文設計了一種汽車輪胎壓力監測系統（Tire Pressure MONITORing System）TPMS及氣壓調節系統的結合使用，該系統能夠對輪胎的參數進行實時監測，當發輪胎壓力參數異常時，及時采取報警措施并進行實時的汽壓調節，從而避免交通事故的發生。論文在對當前存在的各種TPMS系統結構形式進行分析和比較后，選用一種現行直接式TPMS結合氣壓調節系統，實現輪胎壓力實時的監測和調節的一種新型系統。提出一種基于直接式TPMS系統的，引入調節功能的新型設計。設計本身解決原有直接式TPMS的電池供電影響系統壽命的瓶頸，保證了監測系統的的穩定性。氣壓調節系統將解決汽車輪胎壓力偏差的問題，在監測到氣壓偏高或者偏低時，對駕駛人員作出警報提醒并實時啟動氣壓調節系統進行胎壓調節，在數他鐘內調節氣壓到標準值，保證行駛的暢順。本文對系統的電源部分，氣壓調節部分進行了分析設計，解決系統供電，信號采集，信號處理及執行調節，RFLF通信通等關鍵技術問題。對硬件進行測試。結果表明，該系統切實可行，成本，通信距離及可靠性方面均達到沒計指標。
標簽： 汽車胎壓監測
上傳時間： 2022-06-19
上傳用戶：kingwide
German universities and scientists have repeatedly set the intermational standard in drive technology. Identification and active compensation of natural frequencies in oscillatory mechanics, status controls with MONITORing structures incorporating acceleration sensors, adaptive compensation of measurement system deficiencies, self-adjusting detent torque compensation… everything invented with only a single aim in mind: to continue improv-ing the motion control, dynamics, precision and processing speed of your machines. For the industrial applicabability of this technology scientific publications in proceedings and laboratory test rigs are not enough. These features consequenty need to be converted into cost-efficient and easily manageable products. That 's exactly what we have done.So in future, if you should need more than today ' smarket can offer you, now everything isgoing to be alright. With our new high-performance ServoOne drive series you will experi-ence
標簽： servoone
上傳時間： 2022-06-24
上傳用戶：kingwide
MotioninterfaceTM is becoming a "must-have"function being adopted by smartphone and tablet manufacturers due to the enormous value it adds to the end user experience. In smartphones, it finds use in applications such as gesture commands for applications and phone control, enhanced gaming, augmented reality, panoramic photo capture and viewing, and pedestrian and vehicle navigation. With its ability to precisely and accurately track user motions, MotionTracking technology can convert handsets and tablets into powerful 3D intelligent devices that can be used in applications ranging from health and fitness MONITORing to location-based services. Key requirements for Motionlnterface enabled devices are small package size, low power consumption, high accuracy and repeatability, high shock tolerance, and application specific performance programmability-all at a low consumer price point.
標簽： mpu6050
上傳時間： 2022-07-06
上傳用戶：zhaiyawei
