<sub id="11661"></sub>
Digitemp Jr. is a device that is designed to Measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically Measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上傳時間： 2013-10-20
上傳用戶：Maple
生活中許多目標的高度和水平距離需要進行測量。目前主要的測量方法，仍以傳統的皮尺丈量為主，測量效率不高，有時還很不方便，沒有技術成熟的數字式測高測距產品。以基本的數學方法為理論依據，利用遙控小車做為載體，采用角度傳感器測量角度、霍爾傳感器測量水平距離等，通過單片機LM3S615進行數據計算，實現了對待測目標物體的高度、水平距離等數據的快速、精確和數字式的測量，高度測量精度可達99.06%，水平測量精度則可達98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be Measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle Measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional Measure instruments. The accuracy of height and distance Measurement can reach 99.06% and 98.06%.
上傳時間： 2013-10-30
上傳用戶：jackandlee
為提高溫度測量效率，降低系統的成本，擴展傳輸距離，設計出一種新型溫度采集系統。單片機通過控制具有單總線方式的溫度傳感器DS18B20實現對溫度的測量，同時單片機通過控制具有單總線方式300～450MHz頻率范圍內的MAX7044與MAX7033無線發射與接收芯片實現溫度數據的無線傳輸。與傳統溫度采集系統相比，該系統利用單總線方式連接，采用無線傳輸方式實現遠距離通信，易于系統的集成與擴展。實驗結果表明，該系統結構簡單、方便移植，能夠同時實現多達上百點溫度的測量與500m范圍的傳輸。 Abstract: To improve the temperature Measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature Measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature Measure-ment and the transmission range of500meters.
上傳時間： 2013-10-29
上傳用戶：515414293
提出一種基于C8051F040的炮塔方位角測試系統的設計方案，給出測試系統的各個模塊軟硬件設計。炮塔方位角測試系統集數據采集，數據傳輸和數據顯示等功能于一體，實現了炮塔方位角裝置的離線檢測。系統軟件采用C51編寫，對單片機進行有效電源管理，保證了系統的穩定性，可靠性。 Abstract: This paper puts forwards a design of artillery position system based on C8051F040，describes all modules hardware and software design of Measurement system.The system has the function of information collection，transmission，and display.It can Measure artillery position system in offline.The system software using C51can manage the power of single chip microcomputer，guarantee the stability，reliability.
上傳時間： 2014-12-27
上傳用戶：7891
介紹了一種基于C8051F020單片機的多路壓力測量儀。該測量儀選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量儀能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量儀具有測量精度高，沖擊小等特點。 Abstract: A Measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can Measure 6 channels signal of the pressure，and the pressure Measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
上傳時間： 2013-11-16
上傳用戶：yare
介紹一種基于單片機的多路溫度采集及監控系統，能夠測量6路溫度信號，具有計算機聯網功能，各測量點可以單獨監控和設置，可根據用戶的需求自動控制。測量溫度范圍為-10 ℃～200 ℃，控制方式采用模擬量調壓模式。該系統具有控制精度高、沖擊小等特點。 Abstract: A temperature collecting and surveillance-controlling system based on sing-chip microcomputer is introduced. It can Measure 6 channel signal of the temperature,and it has a function of network connection.The temperature Measure points can be monitored and located, it can be controlled automatic according to user’s demand.The temperature range is -10℃ to 200℃.The model of control is adjustable voltage with simulation. It features high precision and little impact.
上傳時間： 2013-10-23
上傳用戶：bjgaofei
為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題，研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心，并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集，并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示，也可以通過紅外方式和PC機進行通訊，在PC機上進行信號的處理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to Measure and show signal detected or transmit to PC by infrared ray.
上傳時間： 2013-11-06
上傳用戶：yy_cn
介紹了一種基于MSP430系列單片機和ADXL203加速度傳感器的數字式傾角儀，它不僅可以實現水平度檢測，而且可以測量00～3600范圍內的任意傾角，分辨率可達O．1。。此外，由于該傾角儀輸出為數字結果，因此它也可以與其他的數字設備結合起來，組合成一個功能更加強大的儀器。該數字傾角儀可廣泛應用于建筑、機械、道路、橋梁、石油、煤礦和地質勘探等各種需要測量重力參考系下傾角的場合。關鍵詞：MSP430F133單片機；力敏傳感器；ADXL203加速度計；角度測量 Abstract：This paper presents a new style digital inclinometer which is developed on the basis of the MSP430F133 MCU and the ADXL203 dual axis aeeelerometer．This inclinometer not only can test levelness，but also can Measure any angle between 0。and 360。with an accuracy of 0．1 O．In addition，its output is a digital result，which makes it possible to integrate itself with other digital devices to form a more functional unit．This inclinometer can be widely used in any construction site，oil field，coal-mine or geologic survey and SO on where it will provide the working people with convenience to Measure any angles．Key words：MSP430F133 MCU；force sensor；ADXL203 accelerometer；angle Measurement
上傳時間： 2013-11-14
上傳用戶：lizhizheng88
基于LabVIEW和單片機的空調溫度場測量系統的研究:室內溫度是空調系統舒適性的重要指標,對其及時、準確地測量顯得非常重要。介紹單片機AT89C51 和數字式、單總線型溫度傳感器DS18B20 組成矩形測量網絡采集空調室內40 點溫度,LabVIEW作為開發平臺,二者之間通過串口實現數據通信,利用LabVIEW強大的數據處理和顯示功能對采集的空調溫度場數據進行實時處理、分析和顯示,詳細介紹了系統的硬件結構和軟件模塊的設計方案。關鍵詞:單片機;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to Measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上傳時間： 2014-05-05
上傳用戶：KSLYZ
單片機系統“PC”失控的軟件措施Software Measure of GettingO uto fC ontrolfo r“PC"in S ingleC hipC omputerS ystem謐 加 春 王 曉 基 雷 小 華(江 西 理 工 大 學機 電 工 程 學 院 ，贛 州 34 10 00)摘要單片機系統在實際工業現場中可能遇到各種干擾和自身的隨機性故障。現場惡劣的環境有可能使計算機系統發生異常，計算機程序指針“PC”失控就是常見的故障之一，如果發生“PC”失控，將導致CPI工作混亂，釀成嚴重的事故。研究了“PC”失控的原因，并指出軟件抗干擾的幾種方法，有效保證單片機系統的正常工作。關鍵詞單片機“PC”失控抗干擾Abstract Inp racticalin dustrialfi elds,th ereis v ariousin terferencea fectingo perationo fsi nglec hipc omputersy stemsa ndt hec omputersy stems。fac噸random faults飾themselves. It is very common that the severe environment makes the computer systems abnormal. The program counter "PC"gettingo utof co ntorlis on eo fth ec ommonfa ults.If th isoc curs,C PUw ouldb eru nningo utof or deran din torducesse riousan cient.T hec ausesof " PC"geting out of control， studied in this paper and some counterMeasures of anti-interference師software are given to ensure single chip computer systemworking properly.Keywords Single。飾computer Porgramc ounter"P C" Anti-interfeernc 在設 計 和 開發單片機系統時，一般難以周全地預計單片機系統在實際工業現場中可能遇到的各種干擾和自身的隨機性故障。因此，除了采取防止和抑制干擾的各項措施外，還應該借助于軟件措施克服某些干擾，系統還應具備迅速自行恢復的能力。本文介紹的應對單片機系統PC失控的軟件措施，設計靈活，節省硬件資源，能保證測控系統長期可靠地運行。MC S- 5 1單片機以其優良的性能價格比大量應用于工業現場測試和控制領域。但是，現場惡劣的環境有可能使計算機系統發生異常，計算機程序指針PC失控就是常見的故障之一，一旦發生PC“走飛”，計算機系統就會出現工作混亂，釀成嚴重的事故。為 了 在 CP 失控時盡量減少由此帶來的不利影響，并盡快使系統恢復正常，需要采取一定的軟件措施和硬件措施。常見的硬件措施有“看門狗”電路。軟件措施設置的前提條件是:①在干擾作用下，微機系統硬件部分不會受到任何損壞，或者損壞部分設置有監測狀態可供查詢;②程序區不會受到干擾侵害。單片機系統的程序和表格以及重要的參數均設置在ROM區，不會因干擾的侵人而改變;③ RAM區中的重要數據不會被破壞，或者雖然被破壞，但是可以重新建立。
上傳時間： 2013-11-02
上傳用戶：bhqrd30
<tt id="66111"></tt>
