亚洲欧美第一页_禁久久精品乱码_粉嫩av一区二区三区免费野_久草精品视频

蟲蟲首頁| 資源下載| 資源專輯| 精品軟件
登錄| 注冊

Multiple-input-Multiple-Output

  • 模塊電源功能性參數指標及測試方法

      模塊電源的電氣性能是通過一系列測試來呈現的,下列為一般的功能性測試項目,詳細說明如下: 電源調整率(Line Regulation) 負載調整率(Load Regulation) 綜合調整率(Conmine Regulation) 輸出漣波及雜訊(Ripple & Noise) 輸入功率及效率(Input Power, Efficiency) 動態負載或暫態負載(Dynamic or Transient Response) 起動(Set-Up)及保持(Hold-Up)時間 常規功能(Functions)測試 1. 電源調整率   電源調整率的定義為電源供應器于輸入電壓變化時提供其穩定輸出電壓的能力。測試步驟如下:于待測電源供應器以正常輸入電壓及負載狀況下熱機穩定后,分別于低輸入電壓(Min),正常輸入電壓(Normal),及高輸入電壓(Max)下測量并記錄其輸出電壓值。 電源調整率通常以一正常之固定負載(Nominal Load)下,由輸入電壓變化所造成其輸出電壓偏差率(deviation)的百分比,如下列公式所示:   [Vo(max)-Vo(min)] / Vo(normal) 2. 負載調整率   負載調整率的定義為開關電源于輸出負載電流變化時,提供其穩定輸出電壓的能力。測試步驟如下:于待測電源供應器以正常輸入電壓及負載狀況下熱機穩定后,測量正常負載下之輸出電壓值,再分別于輕載(Min)、重載(Max)負載下,測量并記錄其輸出電壓值(分別為Vo(max)與Vo(min)),負載調整率通常以正常之固定輸入電壓下,由負載電流變化所造成其輸出電壓偏差率的百分比,如下列公式所示:   [Vo(max)-Vo(min)] / Vo(normal)    3. 綜合調整率   綜合調整率的定義為電源供應器于輸入電壓與輸出負載電流變化時,提供其穩定輸出電壓的能力。這是電源調整率與負載調整率的綜合,此項測試系為上述電源調整率與負載調整率的綜合,可提供對電源供應器于改變輸入電壓與負載狀況下更正確的性能驗證。 綜合調整率用下列方式表示:于輸入電壓與輸出負載電流變化下,其輸出電壓之偏差量須于規定之上下限電壓范圍內(即輸出電壓之上下限絕對值以內)或某一百分比界限內。 4. 輸出雜訊   輸出雜訊(PARD)系指于輸入電壓與輸出負載電流均不變的情況下,其平均直流輸出電壓上的周期性與隨機性偏差量的電壓值。輸出雜訊是表示在經過穩壓及濾波后的直流輸出電壓上所有不需要的交流和噪聲部份(包含低頻之50/60Hz電源倍頻信號、高于20 KHz之高頻切換信號及其諧波,再與其它之隨機性信號所組成)),通常以mVp-p峰對峰值電壓為單位來表示。   一般的開關電源的規格均以輸出直流輸出電壓的1%以內為輸出雜訊之規格,其頻寬為20Hz到20MHz。電源實際工作時最惡劣的狀況(如輸出負載電流最大、輸入電源電壓最低等),若電源供應器在惡劣環境狀況下,其輸出直流電壓加上雜訊后之輸出瞬時電壓,仍能夠維持穩定的輸出電壓不超過輸出高低電壓界限情形,否則將可能會導致電源電壓超過或低于邏輯電路(如TTL電路)之承受電源電壓而誤動作,進一步造成死機現象。   同時測量電路必須有良好的隔離處理及阻抗匹配,為避免導線上產生不必要的干擾、振鈴和駐波,一般都采用雙同軸電纜并以50Ω于其端點上,并使用差動式量測方法(可避免地回路之雜訊電流),來獲得正確的測量結果。 5. 輸入功率與效率   電源供應器的輸入功率之定義為以下之公式:   True Power = Pav(watt) = Vrms x Arms x Power Factor 即為對一周期內其輸入電壓與電流乘積之積分值,需注意的是Watt≠VrmsArms而是Watt=VrmsArmsxP.F.,其中P.F.為功率因素(Power Factor),通常無功率因素校正電路電源供應器的功率因素在0.6~0.7左右,其功率因素為1~0之間。   電源供應器的效率之定義為為輸出直流功率之總和與輸入功率之比值。效率提供對電源供應器正確工作的驗證,若效率超過規定范圍,即表示設計或零件材料上有問題,效率太低時會導致散熱增加而影響其使用壽命。 6. 動態負載或暫態負載   一個定電壓輸出的電源,于設計中具備反饋控制回路,能夠將其輸出電壓連續不斷地維持穩定的輸出電壓。由于實際上反饋控制回路有一定的頻寬,因此限制了電源供應器對負載電流變化時的反應。若控制回路輸入與輸出之相移于增益(Unity Gain)為1時,超過180度,則電源供應器之輸出便會呈現不穩定、失控或振蕩之現象。實際上,電源供應器工作時的負載電流也是動態變化的,而不是始終維持不變(例如硬盤、軟驅、CPU或RAM動作等),因此動態負載測試對電源供應器而言是極為重要的。可編程序電子負載可用來模擬電源供應器實際工作時最惡劣的負載情況,如負載電流迅速上升、下降之斜率、周期等,若電源供應器在惡劣負載狀況下,仍能夠維持穩定的輸出電壓不產生過高激(Overshoot)或過低(Undershoot)情形,否則會導致電源之輸出電壓超過負載組件(如TTL電路其輸出瞬時電壓應介于4.75V至5.25V之間,才不致引起TTL邏輯電路之誤動作)之承受電源電壓而誤動作,進一步造成死機現象。 7. 啟動時間與保持時間   啟動時間為電源供應器從輸入接上電源起到其輸出電壓上升到穩壓范圍內為止的時間,以一輸出為5V的電源供應器為例,啟動時間為從電源開機起到輸出電壓達到4.75V為止的時間。   保持時間為電源供應器從輸入切斷電源起到其輸出電壓下降到穩壓范圍外為止的時間,以一輸出為5V的電源供應器為例,保持時間為從關機起到輸出電壓低于4.75V為止的時間,一般值為17ms或20ms以上,以避免電力公司供電中于少了半周或一周之狀況下而受影響。    8. 其它 在電源具備一些特定保護功能的前提下,還需要進行保護功能測試,如過電壓保護(OVP)測試、短路保護測試、過功保護等

    標簽: 模塊電源 參數 指標 測試方法

    上傳時間: 2013-10-22

    上傳用戶:zouxinwang

  • 用于汽車無線電和信息娛樂系統的8V開關電源

    Abstract: This application note illustrates an intermediate 8V switching power supply for an automotive radio and infotainment system.The design withstands the complete automotive input voltage range (including cold crank and load dump conditions), assuring a stable8V supply for common subsystems such as a CD driver, LCDs, and a radio module in modern infotainment systems. To avoiddisturbance in the AM and FM bands, the switching power supply runs at a fixed frequency of 2MHz, enabling an ideal solution forradio systems.

    標簽: 汽車無線電 信息娛樂系統 開關電源

    上傳時間: 2013-11-20

    上傳用戶:feitian920

  • 電源供應器與數字電位器校準應用筆記

    Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.

    標簽: 電源供應器 數字電位器 應用筆記 校準

    上傳時間: 2013-10-31

    上傳用戶:caiguoqing

  • 使用H橋變壓器驅動器,充電超級電容器

    Abstract: With its small size and large load (10W) capability, the MAX13256 H-bridge transformer driver is an attractive solution forcharging supercapacitors (supercaps). However, a large capacitance on the output of the circuit can force the driver into fault modeat startup, due to the high initial charge current. This application note presents a solution that allows users to charge a largecapacitance without going into fault.

    標簽: H橋變壓器 驅動器 充電 超級電容器

    上傳時間: 2013-10-20

    上傳用戶:2728460838

  • 簡單、高效USB電源管理IC解決方案

      Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.

    標簽: USB 電源管理IC 方案

    上傳時間: 2013-11-02

    上傳用戶:名爵少年

  • 單片同步穩壓器驅動外部元件負載

      The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and capacitors.

    標簽: 同步穩壓器 元件 驅動 負載

    上傳時間: 2014-01-03

    上傳用戶:dongbaobao

  • MAX14885E VGA交叉開關電源排序

      The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.

    標簽: 14885E 14885 MAX VGA

    上傳時間: 2013-10-23

    上傳用戶:wuchunzhong

  • FP6291

    DC/DC 升壓IC:The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.

    標簽: 6291 FP

    上傳時間: 2013-11-07

    上傳用戶:3294322651

  • DN387 級聯7A點的負載單片降壓轉換器

      Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.

    標簽: 387 DN 級聯 負載

    上傳時間: 2013-10-18

    上傳用戶:avensy

  • DN383 高電壓電流模式降壓轉換器

      Low power standby requirements are typically associatedwith battery-powered systems. Automotive systems,for example, commonly require power supplies tomaintain output voltage regulation even under no-loadconditions—while drawing minimal quiescent current topreserve battery life. Rising energy costs, however, haveextended the need for low current standby operation toline-powered systems, such as small plugged-in appliancesfor home and business.

    標簽: 383 DN 高電壓 電流模式

    上傳時間: 2013-11-20

    上傳用戶:xinyuzhiqiwuwu

主站蜘蛛池模板: 明水县| 西和县| 沅陵县| 唐海县| 阳山县| 西充县| 无锡市| 定远县| 运城市| 安仁县| 葫芦岛市| 伊吾县| 如皋市| 广东省| 南投县| 吴忠市| 彭山县| 长乐市| 龙口市| 佛冈县| 望都县| 普定县| 当雄县| 全南县| 慈溪市| 五指山市| 贡嘎县| 同心县| 喀喇沁旗| 内丘县| 秭归县| 墨江| 札达县| 榕江县| 东至县| 通化市| 迁西县| 丽江市| 朝阳市| 江源县| 谢通门县|