提供了解決protel99se與win7系統在添加sch和pcb庫時出現的“file is not recognised”的問題，比較全面。
上傳時間： 2013-11-21
上傳用戶：yunfan1978
PCB methodologies originated in the United States.Units of measurement are therefore typically in Imperial units, not SI/metric units.
標簽： 布局技術
上傳時間： 2014-01-07
上傳用戶：asdkin
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上傳時間： 2013-10-15
上傳用戶：busterman
在Protel2004中進行PCB的完備的CAM輸出。首先，我們可以輸出的gerber文件， 操作如下：1：畫好PCB后，在PCB 的文件環境中，左鍵點擊File\Fabrication Outputs\Gerber Files,進入Gerber setup 界面
上傳時間： 2013-10-14
上傳用戶：aeiouetla
Abstract: Electrolytic capacitors are notorious for short lifetimes in high-temperature applications such asLED light bulbs. The careful selection of these devices with proper interpretation of their specifications isessential to ensure that they do not compromise the life of the end product. This application notediscusses this problem with electrolytic capacitors in LED light bulbs and provides an analysis that showshow it is possible to use electrolytics in such products.
上傳時間： 2013-11-17
上傳用戶：asdfasdfd
The LTP5900 includes sufficient power supply filtering and decoupling capacitancesuch that additional filtering should not be necessary for most battery-powereddesigns. Care must be taken to avoid large transient voltages on the supply as theM2510 steps up its current consumption (see the section on Supply Design below).
標簽： Integration Hardware Guide 5900
上傳時間： 2014-12-24
上傳用戶：youmo81
In industrial applications, high voltage power supply spikes with durations ranging from a few microseconds to hundreds of millisecondsare commonly encountered. The electronics in these systems must not only survive transient voltage spikes, but in many cases alsooperate reliably throughout the event.
上傳時間： 2013-11-07
上傳用戶：redmoons
Abstract: It may sound trite, but it is definitely true: the smart grid has the potential to completely transform the energyindustry. However, smart meters and grid management alone will not ensure the success of the smart grid. Unliketraditional IT networks, smart grids require consideration of energy measurement and security. To completely optimize thistechnology, smart grid designs must focus on energy measurement and security. This tutorial considers the benefits ofboth energy measurement and security and how they make machine-to-machine networks different from traditional IT.
上傳時間： 2013-10-29
上傳用戶：皇族傳媒
Abstract: Stuxnet, a sophisticated virus that damaged Iran's nuclear capability, should be an eye openerfor the world. We can choose to learn something very narrow (how to combat the Stuxnet virus) or wecan choose to focus on the larger goal of thwarting the next type of creative cyber attack. Unfortunately,critical industrial infrastructure is not currently designed with security as a key goal, leaving open multipleavenues for an educated and funded attacker to create massive problems. This tutorial outlines somebasic concepts that engineers and product definers should consider to make sure their new projects stayahead of future threats.
上傳時間： 2013-11-17
上傳用戶：llwap
Abstract: Investment in smart meters and smart grid end equipment continues to grow worldwide as countriestry to make their electric delivery systems more efficient. However, as critical as the electric deliveryinfrastructure is, it is normally not secured and thus subject to attack. This article describes the concept oflife-cycle security—the idea that embedded equipment in the smart grid must have security designed into theentire life of the product, even back to the contract manufacturer. We also talk about how life-cycle securityapplies to embedded equipment in the smart grid. Potential threats are discussed, as are potential solutionsto mitigate the risks posed by those threats.
上傳時間： 2014-12-24
上傳用戶：熊少鋒
