Handheld designers often grapple with ways to de-bounceand control the on/off pushbutton of portable devices.Traditional de-bounce designs use discrete logic, fl ipflops, resistors and capacitors. Other designs includean onboard microprocessor and discrete comparatorswhich continuously consume battery power. For highvoltage multicell battery applications, a high voltageLDO is needed to drive the low voltage devices. All thisextra circuitry not only increases required board spaceand design complexity, but also drains the battery whenthe handheld device is turned off. Linear Technology addressesthis pushbutton interface challenge with a pairof tiny pushbutton controllers.
上傳時間： 2013-11-18
上傳用戶：ZJX5201314
The LTC®3569 is a compact power solution for handhelddevices. Its tiny 3mm × 3mm QFN package includesthree buck regulators with individually programmableoutput voltages. One regulator supports load currentsup to 1200mA, while the other two support currents to600mA. Two regulators can be paralleled for increasedload capability. Each current-mode regulator is internallycompensated with excellent load and line regulation. Acomplete 2- or 3-output solution requires a minimumof external passive components.
上傳時間： 2013-10-11
上傳用戶：yxgi5
Many system designers need an easy way to producea negative 3.3V power supply. In systems that alreadyhave a transformer, one option is to swap out the existingtransformer with one that has an additional secondarywinding. The problem with this solution is that manysystems now use transformers that are standard, offthe-shelf components, and most designers want toavoid replacing a standard, qualifi ed transformer with acustom version. An easier alternative is to produce thelow negative voltage rail by stepping down an existingnegative rail. For example, if the system already employsan off-the-shelf transformer with two secondary windingsto produce ±12V, and a –3.3V rail is needed, a negativebuck converter can produce the –3.3V output from the–12V rail.
上傳時間： 2013-10-09
上傳用戶：Jerry_Chow
One of the fi rst lessons in a basic electronics coursecovers the symbols for resistors, capacitors, inductors,voltage sources and current sources. Althougheach symbol represents a functional component of areal-world circuit, only some of the symbols have directphysical counterparts. For instance, the three discretepassive devices—resistors, capacitors, inductors—canbe picked off a shelf and placed on a real board muchas their symbolic analogs appear in a basic schematic.Likewise, while voltage sources have no direct 2-terminalanalog, a voltage source can be easily built with an offthe-shelf linear regulator.
上傳時間： 2013-11-24
上傳用戶：simonpeng
Abstract: As electronic systems take over many of the mechanical functions in a car—ranging from engine timing to steering andbraking—there is a growing concern about fault tolerance. There should not be a single point of failure that would prevent a car fromat least "limping" off the road or making it to the nearest service station. Redundant systems, watchdog timers, and other controlcircuits are used to reroute signals and perform other functions that ensure that a vehicle can safely make it off the road when afailure occurs.
上傳時間： 2013-11-10
上傳用戶：diets
為了改變目前電網現場作業管理的變電巡檢、變電檢修試驗、輸電線路巡檢檢修等管理系統各自獨立運行，信息不能共享，功能、效率受限，建設和維護成本高的現狀，提出了采用B/S+C/S構架模式，將各現場作業管理模塊和生產MIS（管理系統）集成為一體的現場作業管理系統的設計方案，做到各子系統和生產MIS軟硬資源共享，做到同一數據唯一入口、一處錄入多處使用。各子系統設備人員等基礎信息來源于生產管理系統，各子系統又是生產管理系統的作業數據、缺陷信息的重要來源。經過研究試用成功和推廣應用，目前該系統已在江西電網220 kV及以上變電站全面應用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上傳時間： 2013-11-15
上傳用戶：han_zh
光伏發電是未來新能源發電重要方向之一，而光伏變流器是光伏發電系統的核心。介紹一種基于微網理念的光伏變流器設計。以該變流器為核心的光伏發電系統可以看做一個小型的微網系統。該系統能根據外部電網情況，工作于并網模式和離網模式。介紹了該系統的各個組成部件的設計以及變流器主電路部分器件的選型。最后，由實驗樣機進行測試。試驗結果驗證了電路拓撲結構及控制方案的可行性，也說明了系統參數設計方法的正確性。 Abstract: Solar Photovoltaic generation is an important direction of new energy power generation in the future，while photovoltaic converter is the core of photovoltaic generation system. This paper deals with a study on photovoltaic inverter based on the concept of microgrid. This paper describes a system whose core component is the photovoltaic inverter，can work on grid-connected mode or run independently according to the external situation. The paper simply describes the main components of the system. At last，the prototype was produced and tested. Test result has proved feasibility of circuit topology structure and controlling scheme and shown correctness of system parameters.Key words: PV inverter； microgrid； off-grid； storage battery
上傳時間： 2014-12-24
上傳用戶：Shaikh
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上傳時間： 2013-10-10
上傳用戶：1184599859
單相橋式逆變電路為例：S1～S4是橋式電路的4個臂，由電力電子器件及輔助電路組成。S1、S4閉合，S2、S3斷開時，負載電壓uo為正S1；S1、S4斷開，S2、S3閉合時，uo為負，把直流電變成了交流電。改變兩組開關切換頻率，可改變輸出交流電頻率。圖5-1 逆變電路及其波形舉例電阻負載時，負載電流io和uo的波形相同，相位也相同。阻感負載時，io滯后于uo，波形也不同（圖5-1b）。t1前：S1、S4通，uo和io均為正。t1時刻斷開S1、S4，合上S2、S3，uo變負，但io不能立刻反向。io從電源負極流出，經S2、負載和S3流回正極，負載電感能量向電源反饋，io逐漸減小，t2時刻降為零，之后io才反向并增大 （2）換流方式分類換流——電流從一個支路向另一個支路轉移的過程，也稱換相。開通：適當的門極驅動信號就可使其開通。關斷：全控型器件可通過門極關斷。半控型器件晶閘管，必須利用外部條件才能關斷，一般在晶閘管電流過零后施加一定時間反壓，才能關斷。研究換流方式主要是研究如何使器件關斷。本章換流及換流方式問題最為全面集中，因此在本章講述1、器件換流利用全控型器件的自關斷能力進行換流（Device Commutation）。2、電網換流由電網提供換流電壓稱為電網換流（Line Commutation）。可控整流電路、交流調壓電路和采用相控方式的交交變頻電路，不需器件具有門極可關斷能力，也不需要為換流附加元件。3、負載換流由負載提供換流電壓稱為負載換流（Load Commutation）。負載電流相位超前于負載電壓的場合，都可實現負載換流。負載為電容性負載時，負載為同步電動機時，可實現負載換流。
上傳時間： 2013-10-15
上傳用戶：qingdou
歐姆龍plc編程軟件CX-Programmer使用手冊 第一章安裝和啟動 1. 安裝 1-1. 安裝CX-Programmer 1-2. 在線注冊 2. 打開新工程和設置設備型號 3. 打開新工程和設置設備型號 4. 主窗口 4-1.兼容SYSWIN軟件的按鍵分配 4-2. 段 4-3.刪除和顯示其他窗口 5.創建程序 5-1.常開接點的輸入 5-2.線圈的輸入 5-3.符號注釋的編輯 5-4.條注釋的輸入 5-5.常閉接點的輸入 5-6.元素注釋的輸入 5-7.上升沿微分接點的輸入 5-8.下降沿微分接點的輸入 5-9.向上垂線的輸入 5-10.向下垂線的輸入 5-11.高級指令的輸入1 - 字符串的輸入 5-12.高級指令的輸入1 - 有用的功能 5-13.輔助繼電器的輸入- 1.0 秒時鐘脈沖位 5-14.高級指令的輸入2 – 微分指令的輸入 5-15.或邏輯的條輸入 5-16.高級指令的輸入3 – 通過功能號來輸入 5-17.定時器指令的輸入 5-18.計數器指令的輸入 5-19.條的編輯…復制和粘貼 5-20. END指令的輸入 第二章在線/調試 1. 程序錯誤檢查(編譯) 2. 進入在線 3. 監視 4. 監視- 2 同時監視程序中多處位置 5. 監視- 3 以十六進制數監視 6. 監視- 4 查看窗口 7. 監視- 5 查看窗口的當前值修改和二進制數監視 8. 查看窗口的有用功能 9. 監視- 6 監視窗口- 2 10.監視- 7 以短條形式顯示 11.監視- 8 微分監視 12.強制為On/Off 13.強制-on/off 位的顯示列表 14.修改定時器的設定值 15.修改定時器的當前值 16.查找功能- 1 通過地址引用工具查找 17.查找功能- 2 梯形圖的折回查找 18.查找功能- 3 通過注釋的關鍵字來查找 19.查找功能- 4 進入條注釋 20.查找功能- 5 查找位地址 21.在線編輯 實用的功能 相關資料： 歐姆龍PLC編程軟件CX-Programmer7.1 簡體中文版
上傳時間： 2013-10-25
上傳用戶：84425894
