using gpio of 2812 This program requires the DSP281x V1.00 header files. As supplied, this project is configured for "boot to H0" operation.
標簽： requires supplied program project
上傳時間： 2013-12-21
上傳用戶：Andy123456
program which uses hashing techniques for storing and retrieving the data. Input to the program: Some random numbers. Input will be from a file. Output: First the program reads all the input and store it properly using some hash techniques. Once your program reads the complete input,it waits for the user input (prompt to the user). User now enters some number.program displays if this number exists in the list or not. it also display the time taken in the search operation.
標簽： program techniques retrieving the
上傳時間： 2017-04-27
上傳用戶：shus521
The Microsoft(R) Guide for Assembly Language and C Programmers By Ray Duncan PROGRAMMING FOR MS-DOS Genealogy of MS-DOS MS-DOS in Operation Structure of MS-DOS Application Programs MS-DOS Programming Tools Keyboard and Mouse Input Video Display Printer and Serial Port File Management Volumes and Directories Disk Internals Memory Management The EXEC Function Interrupt Handlers Installable Device Drivers Filters Compatibility and Portability MS-DOS FUNCTIONS REFERENCE IBM ROM BIOS AND MOUSE FUNCTIONS REFERENCE LOTUS/INTEL/MICROSOFT EMS FUNCTIONS REFERENCE
標簽： Programmers PROGRAMMING Microsoft Assembly
上傳時間： 2017-05-05
上傳用戶：xuanjie
Software uart using a general purpose io and an external interrupt pin of an atmel uc. half duplex operation, adjustable baud rate
標簽： interrupt Software external general
上傳時間： 2013-12-31
上傳用戶：zhangyigenius
USBHostSlave is a USB 1.1 host and Device IP core. – Supports full speed (12Mbps) and low speed (1.5Mbps) operation. – USB Device has four endpoints, each with their own independent FIFO. – Supports the four types of USB data transfer control, bulk, interrupt, and isochronous transfers. – Host can automatically generate SOF packets. – 8-bit Wishbone slave bus interface. – FIFO depth configurable via paramters.
標簽： speed USBHostSlave and Supports
上傳時間： 2014-01-17
上傳用戶：sxdtlqqjl
The most straightforward approximation is the standard Gaussian approximation, where the MAI is approximated by a Gaussian random variable. This approximation is simple, however it is not accurate in general. In situations where the number of users is not large, the Gaussian approximation is not appropriate. In-depth analysis of must be applied. The Holtzman?s improved Gaussian approximation provides a better approximation to the MAI term. The approximation conditions the interference term on the operation condition of each user.
標簽： approximation straightforward the Gaussian
上傳時間： 2017-06-03
上傳用戶：dyctj
The Hilbert Transform is an important component in communication systems, e.g. for single sideband modulation/demodulation, amplitude and phase detection, etc. It can be formulated as filtering operation which makes it possible to approximate the Hilbert Transform with a digital filter. Due to the non-causal and infinite impulse response of that filter, it is not that easy to get a good approximation with low hardware resource usage. Therefore, different filters with different complexities have been implemented. The detailed discussion can be found in "Digital Hilbert Transformers or FPGA-based Phase-Locked Loops" (http://ieeexplore.ieee.org/xpl/freeabs_all.jsp?arnumber=4629940). The design is fully pipelined for maximum throughput.
標簽： e.g. communication Transform important
上傳時間： 2017-06-25
上傳用戶：gxf2016
This program requires the DSP2833x header files. // // This program requires an external I2C RTC connected to // the I2C bus at address 0x6f. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
標簽： requires program This external
上傳時間： 2017-07-12
上傳用戶：dianxin61
This program requires the DSP2833x header files. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
標簽： configured requires supplied program
上傳時間： 2014-01-10
上傳用戶：lixinxiang
The MINI2440 is an effecient ARM9 development board with a comprehensive price, it characterizes simple method and high performance-price ratio. Based on the Samsung S3C2440 microprocessor, it embodies professional stable CPU core power source chip and reset chip to ensure the stability of the system operation. The PCB on the MINI2440 board is designed to be 4-layers board, adopting the ENIG technology and professional equal-length wiring to ensure the completeness of the signals of the key signal wires and manufactured and released under stringent quality control plans. With the help of this detailed manual, users are supposed to become proficient in the development process of embedded Linux and WinCE operating system, they are supposed to get the foundation, so long as they have obtained the basic and necessary knowledge about the C language, in two weeks.
標簽： comprehensive characterizes development effecient
上傳時間： 2013-12-18
上傳用戶：csgcd001
