<li id="e8a6a"></li> <li id="e8a6a"></li> The code is for Auxiliary IO module which supports 16 inputs and 16 OUTPUTs and Modbus protocol
標簽： Auxiliary and supports protocol
上傳時間： 2017-07-21
上傳用戶：wang0123456789
19.2 Mbps 4x4 BLAST&MIMO detector with soft ML OUTPUTs。純英文論文，外國文獻
上傳時間： 2015-04-21
上傳用戶：asdf20
英文描述： BCD to 7-Segment Decoder/Driver with Open-Collector OUTPUTs 中文描述： BCD碼到7段解碼器/驅動器，集電極開路輸出
上傳時間： 2013-07-14
上傳用戶：m62383408
英文描述： BCD-to-Seven-Segment Decoder Driver(Internal Pull-up OUTPUTs) 中文描述： BCD碼到七段解碼器驅動程序（內部上拉輸出）
上傳時間： 2013-07-13
上傳用戶：cc1015285075
英文描述： Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flops with Clear and Complementary OUTPUTs 中文描述： 雙下降沿觸發主從JK觸發器明確和互補輸出
上傳時間： 2013-04-24
上傳用戶：黃華強
Precision 16-bit analog OUTPUTs with softwareconfigurableoutput ranges are often needed in industrialprocess control equipment, analytical and scientificinstruments and automatic test equipment. In the past,designing a universal output module was a daunting taskand the cost and PCB real estate associated with thisfunction were problematic, if not prohibitive.
上傳時間： 2014-12-23
上傳用戶：如果你也聽說
Recent advances in low voltage silicon germaniumand BiCMOS processes have allowed the design andproduction of very high speed amplifi ers. Because theprocesses are low voltage, most of the amplifi er designshave incorporated differential inputs and OUTPUTs to regainand maximize total output signal swing. Since many lowvoltageapplications are single-ended, the questions arise,“How can I use a differential I/O amplifi er in a single-endedapplication?” and “What are the implications of suchuse?” This Design Note addresses some of the practicalimplications and demonstrates specifi c single-endedapplications using the 3GHz gain-bandwidth LTC6406differential I/O amplifi er.
上傳時間： 2013-11-23
上傳用戶：rocketrevenge
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having OUTPUTs based on a frequency or phase, have an advantage over conventional analogue sensors in that their OUTPUTs can be measured directly in digital systems by pulse counting.
上傳時間： 2013-10-08
上傳用戶：wuyuying
在Protel2004中進行PCB的完備的CAM輸出。首先，我們可以輸出的gerber文件， 操作如下：1：畫好PCB后，在PCB 的文件環境中，左鍵點擊File\Fabrication OUTPUTs\Gerber Files,進入Gerber setup 界面
上傳時間： 2013-10-14
上傳用戶：aeiouetla
Many telecommunications and computing applicationsneed high effi ciency step-down DC/DC converters thatcan operate from a very low input voltage. The highoutput power synchronous controller LT3740 is idealfor these applications, converting input supplies rangingfrom 2.2V to 22V to OUTPUTs as low as 0.8V with loadcurrents from 2A to 20A. Applications include distributedpower systems, point-of-load regulation and conversionof logic supplies.
上傳時間： 2013-11-05
上傳用戶：zhf01y
