protel s help on line
上傳時間： 2013-09-18
上傳用戶：iswlkje
•Founded in Jan. 08, 2001 in Shanghai, China.•Fabless IDH focused on Analog & Mixed Signal Chip design & marketing •Over 100 IC introduced.•Over 200 OEM Customer worldwide•ISO-9000 Certified•Distribution Channel in Taiwan, China & Japan To achieve 100% customer satisfactionby producing the technically advanced product with the best quality, on-time delivery and service. Leverages on proprietary process and world-class engineering team to develop innovative & high quality analog solutions that add value to electronics equipment.
標簽： Circuit Analog Design Porta
上傳時間： 2013-10-24
上傳用戶：songnanhua
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上傳時間： 2013-10-15
上傳用戶：busterman
電子設備的 ON/OFF 按鈕給繫統設計師帶來了一組獨特的挑戰
上傳時間： 2013-10-13
上傳用戶：18165383642
The P89LPC912/913/914 are single-chip microcontrollers in low-cost 14-pin packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system level functions have been incorporated into the P89LPC912/913/914 in order to reduce component count, board space, and system cost.
上傳時間： 2013-10-12
上傳用戶：司令部正軍級
現有基于MAX7219芯片的數碼管驅動電路只適用于小尺寸LED，為擴展其使用范圍，在介紹動態顯示芯片MAX7219功能的基礎上，提出了一個基于該芯片的8位高亮度8英寸數碼管驅動電路。電路保留了MAX7219芯片的功能強大、編程簡單等優點，通過74LS273鎖存器和ULN2803達林頓驅動器，實現了對任意大尺寸數碼管提供較高電壓和電流驅動的靜態顯示，并亮度可調。 Abstract: The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with higher voltage and current was achieved with the help of 74LS273 and ULN2803.
上傳時間： 2013-10-23
上傳用戶：31633073
為提高電容測量精度，針對電容式傳感器的工作原理設計了基于PIC16LF874單片機電容測量模塊。簡單闡述了電容測量電路的應用背景和國內外研究現狀，介紹了美國Microchip公司PIC16LF874單片機的特性。電容式傳感器輸出的動態微弱電容信號通過PS021型電容數字轉換器把模擬量數據轉換成數字量數據，所測數據由PIC16LF874單片機應用程序進行處理、顯示和保存。實驗結果表明，固定電容標稱值為10~20 pF 的測量值相對誤差在1%以內，同時也可知被測電容容值越大，測量值和標稱值相對誤差越小。 Abstract: To improve the accuracy of capacitance measurement，aimed at the principle of work of mercury capacitance acceleration transducer，the design of micro capacitance measurement circuit is based on the key PIC16LF874 chip. Briefly discusses the application of the capacitance measuring circuit for the background and status of foreign researchers，focusing on the United States PIC16LF874 microcontroller features. Capacitive sensor outputed signal through the dynamics of weak PS021-chip capacitors （capacitancedigital converter） to convert analog data into digital data，the measured data from the PIC16LF874 microcontroller application process， display and preservation. Experimental results show that the fixed capacitor 10pF ~ 20pF nominal value of the measured value of relative error is within 1%，but also it canbe seen the value of the measured capacitance larger，measuring value and the nominal value of relative error smaller.
上傳時間： 2013-10-29
上傳用戶：wojiaohs
提出一種基于凌陽單片機的步進電機加減速的控制方法。采用凌陽科技推出的16位結構工控單片機SPMC75F2413A為控制器，由Allegro公司生產的兩相步進電機專用驅動器件SLA7042M構成步進電機的驅動電路，在傳統的3段直線加減速控制算法基礎上增加至7段S形曲線加減速過程，控制步進電機的啟動和停止。實驗結果表明，該控制方法克服了直線加減速中不連續、易造成系統沖擊的問題，整個系統實現柔性控制，電機啟動、停止連續性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上傳時間： 2013-12-08
上傳用戶：jiangfire
為提高太陽能的利用率，以ATmega8單片機為控制核心，設計了一套光電跟蹤與視日運動軌跡跟蹤互補控制的雙軸太陽跟蹤器。該跟蹤器在晴天時，利用光敏電阻采集光強判斷太陽位置,控制步進電機實現光電跟蹤；在陰天時，采集時鐘器件PCF8583的時間信息,計算當前太陽位置來實現視日運動軌跡跟蹤。實驗表明：該太陽跟蹤器能在不同天氣狀況下對太陽進行較準確地跟蹤，能量接收效率提高了30%，達到充分利用太陽能的目的。 Abstract: To improve the utilization rate of solar energy，a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days，the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking，n cloudy days，it collects clock chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental results show the solar tracking controller accurately tracks the sun in different weather conditions，improves received energy efficiency by30%and reaches the purpose of full use of solar energy.
上傳時間： 2013-10-15
上傳用戶：urgdil
設計一種基于P89V51RD2的功率因數測量儀，采用光電隔離器和專用數碼管驅動器。該測量儀是以增強型單片機P89V51RD2為核心，大大簡化系統硬件設計。而軟件部分采用模塊化設計思想，采用中值濾波和小數補償算法，實現功率因數的高精度測量。實驗測試表明，該功率因數測量儀測量精度高，運行穩定可靠。 Abstract: A power－factor measurement instrument based on P89V51RD2is designed，which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore，modularization software is developed in detail.The high precision power－factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power－ factor measurement instrument is high precision，steady and reliable.
上傳時間： 2014-12-27
上傳用戶：CHINA526
