Boost LED drivers are often used to drive LEDs in series. If an LED fails while open,Overvoltage protection (OVP) is necessary to avoid the damage to a boost integrated circuit (IC) or output capacitor. This application report presents the solutions to increase the TPS61043 LED driver OVP threshold.
標簽： Overvoltage Protection Solutions Driver
上傳時間： 2013-10-14
上傳用戶：jiangfire
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,Overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上傳時間： 2013-11-23
上傳用戶：新手無憂
為了有效地提升鉛酸蓄電池的使用壽命，同時實現對充電過程的監控，設計出一種用單片機控制的36 V鉛酸蓄電池充電電源。本電路采用反激式拓撲，連續電流工作模式，電源管理IC設計在電源的副邊，由ELAN公司的EM78P258N單片機模擬，是用可編程器件模擬電源管理IC，實現智能電源低成本化的一次成功嘗試，通過對單片機的軟件設計實現了充電電源的狀態顯示、充電時間控制、報警、過溫保護、過壓保護、過流保護等功能。本充電器真正的實現了鉛酸蓄電池的三段式充電過程，其最高輸出功率可達90 W，效率約85%，成本不到20元，具有很高的市場競爭力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and Overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上傳時間： 2013-11-16
上傳用戶：cepsypeng
FFeeaattuurreess ? Input voltage range: 2.2 to 6V ? Programmable LED Current ? Drives LEDs Up to 27V ? Switching Frequency：up to 800KHz ? Wide dimming frequency range: 20KHz~ 360 KHz ? Programmable Overvoltage Protection ? Tiny SOP8/PP Package
標簽： HX3248C
上傳時間： 2021-11-05
上傳用戶：aben
CHAPTER 1: THE OP AMP CHAPTER 2: OTHER LINEAR CIRCUITS CHAPTER 3: SENSORS CHAPTER 4: RF/IF CIRCUITS CHAPTER 5: FUNDAMENTALS OF SAMPLED DATA SYSTEMS CHAPTER 6: CONVERTERS CHAPTER 7: DATA CONVERTER SUPPORT CIRCUITS CHAPTER 8: ANALOG FILTERS CHAPTER 9: POWER MANAGEMENT CHAPTER 10: PASSIVE COMPONENTS CHAPTER 11: Overvoltage EFFECTS ON ANALOG INTEGRATED CIRCUITS CHAPTER 12: PRINTED CIRCUIT BOARD (PCB) DESIGN ISSUES CHAPTER 13: DESIGN DEVELOPMENT TOOLS
上傳時間： 2021-12-21
上傳用戶：wangshoupeng199
The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input Overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
標簽： pw2601
上傳時間： 2022-02-11
上傳用戶：
鋰電池BMS管理技術是移動機器人的關鍵技術,本文設計了基于bq76PL455、STM32F103的鋰電池管理系統,實現了電池組電壓、電流、過壓、過流等狀態監測;系統配置均衡電路,電池充電過程中若出現電池單體電壓不平衡現象,會觸發均衡電路,進而提高電池的安全性,延長使用壽命。Lithium battery BMS management technology is the key technology of mobile robot.The lithium battery management system based on bq76PL455 and STM32F103 is proposed to realize the monitoring of battery pack voltage,current,Overvoltage and overcurrent.The system is equipped with equalization circuit.When the battery cell voltage imbalance occurs,the equalization circuit is triggered to improve the safety and service life of the battery.
上傳時間： 2022-04-02
上傳用戶：
