以太網和CAN總線應用廣泛，但由于其通信協議不同，兩種總線器件間無法進行數據通信，因此，設計了基于CP2200與C8051F040的以太網總線與CAN總線接口轉換電路，并給出部分相關硬件電路與軟件設計分析。在保證數據完整和協議可靠的前提下，通過握手協議和簡化的以太網協議，不僅實現了以太網數據與CAN數據的轉發，同時還順利的解決了以太網的高速性與CAN的低速率沖突，以及兩者數據包之間的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating between two kinds of bus device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
上傳時間： 2013-10-15
上傳用戶：Ants
提出一種基于凌陽單片機的步進電機加減速的控制方法。采用凌陽科技推出的16位結構工控單片機SPMC75F2413A為控制器，由Allegro公司生產的兩相步進電機專用驅動器件SLA7042M構成步進電機的驅動電路，在傳統的3段直線加減速控制算法基礎上增加至7段S形曲線加減速過程，控制步進電機的啟動和停止。實驗結果表明，該控制方法克服了直線加減速中不連續、易造成系統沖擊的問題，整個系統實現柔性控制，電機啟動、停止連續性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上傳時間： 2013-12-08
上傳用戶：jiangfire
為提高太陽能的利用率，以ATmega8單片機為控制核心，設計了一套光電跟蹤與視日運動軌跡跟蹤互補控制的雙軸太陽跟蹤器。該跟蹤器在晴天時，利用光敏電阻采集光強判斷太陽位置,控制步進電機實現光電跟蹤；在陰天時，采集時鐘器件PCF8583的時間信息,計算當前太陽位置來實現視日運動軌跡跟蹤。實驗表明：該太陽跟蹤器能在不同天氣狀況下對太陽進行較準確地跟蹤，能量接收效率提高了30%，達到充分利用太陽能的目的。 Abstract: To improve the utilization rate of solar energy，a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days，the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking，n cloudy days，it collects clock chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental results show the solar tracking controller accurately tracks the sun in different weather conditions，improves received energy efficiency by30%and reaches the purpose of full use of solar energy.
上傳時間： 2013-10-15
上傳用戶：urgdil
設計一種基于ATmega16L單片機的溫度控制系統，闡述該系統的軟硬件設計方案。采用模塊化設計方法，利用增量式PID算法使被控對象的溫度值趨于給定值。實驗結果表明該系統具有良好的檢測和控制功能。 Abstract: This paper designs a temperature control system based on ATmega16L，describes the hardware and software de－sign scheme of the system，adopts the modularized design method and utilizes the incremental PID algorithm to realize the temperature of controlled device incline to the given value.The experiment result indicates that the system has good detec－tion and control function
上傳時間： 2013-10-09
上傳用戶：stvnash
設計一種基于P89V51RD2的功率因數測量儀，采用光電隔離器和專用數碼管驅動器。該測量儀是以增強型單片機P89V51RD2為核心，大大簡化系統硬件設計。而軟件部分采用模塊化設計思想，采用中值濾波和小數補償算法，實現功率因數的高精度測量。實驗測試表明，該功率因數測量儀測量精度高，運行穩定可靠。 Abstract: A power－factor measurement instrument based on P89V51RD2is designed，which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore，modularization software is developed in detail.The high precision power－factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power－ factor measurement instrument is high precision，steady and reliable.
上傳時間： 2014-12-27
上傳用戶：CHINA526
首先研究CAN總線和SAE J1939協議，提出一種基于MC9S12HZ256微控制器的總線式汽車數字儀表解決方案。詳細介紹SAE J1939協議的報文幀格式及應用層協議中發動機相關參數的定義，以及步進電機及其驅動和車速信號的處理方法。該數字儀表系統硬件平臺由微處理器和信號采集和信息處理及顯示等模塊組成。軟件設計部分編程實現了對CAN總線和各傳感器數據的讀取、處理。該系統能夠實時反映車輛工況。 Abstract: In this paper，CAN bus and SAE J1939protocol are researched，and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper motor and its driver，the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU，signal acquisition mod-ule，and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming，and vehicle condition can be reflected in real-time.
上傳時間： 2013-10-20
上傳用戶：huannan88
詳細介紹工控軟件組態王與單片機多機串口通訊的設計原理。分析組態王提供的直接與單片機串口通信方法的優點，給出系統基于RS-485總線傳輸的接口電路原理圖。根據組態王提供的通訊協議和單片機多機串口通訊的原理，給出程序設計流程與思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上傳時間： 2013-12-19
上傳用戶：tecman
實時時鐘是微機保護裝置的重要部件，在討論PCF8583結構與功能的基礎上，提出采用dsPIC33F系列微處理器與串行I2C時鐘PCF8583的接口設計方案，給出了相應的接口電路與軟件流程。該設計方案結構簡單，可靠性高，開發周期短，具有一定的實用與參考價值。所設計的微機保護裝置已投入現場運行，效果良好。 Abstract: Real-time clock chip is an important part in microcomputer protection device.Based on discussing the structure and function of PCF8583，a new interface scheme which uses dsPIC33F microprocessor and serial clock chip（I2C）PCF8583is proposed.The method of the circuit design and the main software flow are introduced in this paper.The scheme has simple structure，higher reliability and shorter exploitation cycle，so has definite practicality or reference value.The microcomputer protection device has been put into operation with better effects.
上傳時間： 2013-11-18
上傳用戶：Thuan
介紹一種基于C8051單片機的動態心電監護系統。該系統由兩部分組成：以C8051F320單片機為核心的數據采集裝置和以PC機為平臺的分析處理系統。硬件電路功耗低，由單片機自帶的USB接口將數據傳送給PC機。軟件平臺采用LabVIEW可視化虛擬儀器系統開發平臺，將傳統儀器的功能模塊集成到計算機中，用戶可通過修改虛擬儀器的程序改變其功能。采用USB接口實時傳輸心電數據，并將數據采集模塊設計為計算機外設，使該系統高速快捷、小巧便攜。 Abstract: In this design，a low-cost ECG electrocardiogram monitoring system is introduced，which consists of two parts:data acquisition device based on C8051F320and PC terminal as the analysis and processing system.The system is low-power consumption，the data is transmitted to the PC terminal by USB interface of the C8051F320.By using the visible virtual instrument system developing platform LabVIEW，the traditional instruments function modules are integrated into the computer，so the user can modify virtual instrument software to change its function to meet their needs.Using USB in-terface to realize real-time ECG data transmission，in addition，ECG data acquisition module is designed as the computer peripheral，which makes the syetem high-speed and portable.
上傳時間： 2013-11-13
上傳用戶：zhangzhenyu
設計一種基于AT89C52的語音錄放系統，利用單片機、ISD2560語音錄放器件、麥克風、揚聲器等元器件實現硬件電路的設計，并利用C51高級語言設計ISD2560器件控制字的寫入和定時中斷程序。經軟硬件調試，結果表明該系統錄放效果良好，具有一定的工程實用價值。 Abstract: Voice recording and playback system based on AT89C52is designed in this paper.Using the single-chip microcomputer，voice recording and playback chip ISD2560，microphone and speaker to realize the hardware circuit design.Writing ISD2560control words and timing interrupt procedures are designed by C51advanced language.Through the hardware and software test,voice recording and playback system play better voice,and this system has some engineering practical values.
上傳時間： 2013-10-20
上傳用戶：ywcftc277
