DC/DC 升壓IC：The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω
power MOSFET make this regulator highly power efficient. The internal compensation network also
minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects
to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current.
The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
應用 APPLICATIONS·電視機、錄像機、音頻設備、顯示器、復印機、打印裝置、游戲機及計算機等。·用于開關電源線性濾波器。·削除 TV、VTR、VCR及監聽器泄漏雜音。·用于OA 設備、通信設備和其它器件。·TV set, recorder, sound-frequency equipment, show-scope, photocopy-scope, typewrite equipment, recreation-scope, computer etc.·For line filters of switching power supplies.·Eliminates incoming/leaking noise of TVs, VTRs/VCRs and audio equipment .·For OA equipment, communications equipment and other electronic devices.
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required.
The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel
Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to
enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements
include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O
configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a
simple solution when additional I/O is needed for ACPI power switches, sensors,
push buttons, LEDs, fans, etc.
The main objective of this book is to present all the relevant informationrequired for RF and micro-wave power amplifier design includingwell-known and novel theoretical approaches and practical design techniquesas well as to suggest optimum design approaches effectively combininganalytical calculations and computer-aided design. This bookcan also be very useful for lecturing to promote the analytical way ofthinking with practical verification by making a bridge between theoryand practice of RF and microwave engineering. As it often happens, anew result is the well-forgotten old one. Therefore, the demonstrationof not only new results based on new technologies or circuit schematicsis given, but some sufficiently old ideas or approaches are also introduced,that could be very useful in modern practice or could contributeto appearance of new ideas or schematic techniques.
When I started writing the first edition of RF Power Amplifiers for Wireless Communications,some time back in 1997, it seemed that I was roaming a largely uninhabitedlandscape. For reasons still not clear to me there were few, if any, otherbooks dedicated to the subject of RF power amplifiers. Right at the same time, however,hundreds of engineers were being assigned projects to design PAs for wirelesscommunications products. It was not, therefore, especially difficult to be successfulwith a book that was fortuitously at the right place and the right time.
