射頻遙控在家電遙控器中的應用電路圖
上傳時間： 2013-11-19
上傳用戶：erkuizhang
Designers of signal receiver systems often need to performcascaded chain analysis of system performancefrom the antenna all the way to the ADC. Noise is a criticalparameter in the chain analysis because it limits theoverall sensitivity of the receiver. An application’s noiserequirement has a signifi cant infl uence on the systemtopology, since the choice of topology strives to optimizethe overall signal-to-noise ratio, dynamic range andseveral other parameters. One problem in noise calculationsis translating between the various units used by thecomponents in the chain: namely the RF, IF/baseband,and digital (ADC) sections of the circuit.
上傳時間： 2014-12-05
上傳用戶：cylnpy
Linear Technology’s High Frequency Product lineupincludes a variety of RF I/Q modulators. The purpose ofthis application note is to illustrate the circuits requiredto interface these modulators with several popular D/Aconverters. Such circuits typically are required to maximizethe voltage transfer from the DAC to the baseband inputsof the modulator, as well as provide some reconstructionfi ltering.
上傳時間： 2013-10-19
上傳用戶：FreeSky
利用MOS場效應管(MOSFET)，采取AB類推挽式功率放大方式，采用傳輸線變壓器寬帶匹配技術，設計出一種寬頻帶高功率射頻脈沖功率放大器模塊，其輸出脈沖功率達1200W，工作頻段0.6M~10MHz。調試及實用結果表明，該放大器工作穩定，性能可靠
上傳時間： 2013-11-17
上傳用戶：waitingfy
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上傳時間： 2014-12-23
上傳用戶：han_zh
射頻電路PCB設計
上傳時間： 2014-01-13
上傳用戶：a1054751988
成功的 RF 設計必須仔細注意整個設計過程中每個步驟及每個細節 這意味著必須在設計開始階段就要進行徹底的 仔細的規劃 并對每個設計步驟的進展進行全面持續的評估 而這種細致的設計技巧正是國內大多數電子企業文化所欠缺的 近幾年來，由于藍芽設備無線局域網絡（WLAN）設備和行動電話的需求與成長 促使業者越來越關注 RF 電路設計的技巧 從過去到現在 RF 電路板設計如同電磁干擾（EMI）問題一樣 一直是工程師們最難掌控的部份 甚至是夢魘 若想要一次就設計成功 必須事先仔細規劃和注重細節才能奏效
上傳時間： 2013-11-13
上傳用戶：liuwei6419
PCB 設計對于電路設計而言越來越重要。但不少設計者往往只注重原理設計,而對PCB 板的設計布局考慮不多,因此在完成的電路設計中常會出現EMC 問題。文中從射頻電路的特性出發,闡述了射頻電路PCB 設計中需要注意的一些問題。
上傳時間： 2013-10-24
上傳用戶：jiangxiansheng
介紹了采用protel 99se進行射頻電路pcb設計的設計流程為了保證電路的性能。在進行射頻電路pcb設計時應考慮電磁兼容性，因而重點討論了元器件的布局與布線原則來達到電磁兼容的目的.關鍵詞 射頻電路 電磁兼容 布局
上傳時間： 2013-11-14
上傳用戶：竺羽翎2222
基于DDS AD9835的高壓射頻信號源的設計
上傳時間： 2013-10-23
上傳用戶：woshiayin
