mp3設計程序資料，采用c語言編寫。 README file for yampp-3 source code 2001-05-27 This is the current state of the yampp-3 source code, 2001-05-27. This code is intended to RUN on Rev. B of the yampp-3 PCB, but can ofcourse be used on compatible systems as well. It still uses the "old" song selection system as the yampp-2. However, the disk handling routines has improved a lot and the obviosly, the new VS1001 handling has been put in. The codesize is almost at it s maximum at 1F40 bytes. A .ROM file is included if you don t have the compiler set up. For now, the documentation is in the code
上傳時間： 2015-04-13
上傳用戶：小碼農lz
SDP Search and Record generator OVERVIEW: Recognizing the difficulty in creating an SDP service description and search from scratch, Microsoft is providing a sample utility in bthnscreate.cxx to automatically create a service or record. This utility can be RUN to create an SDP record or to setup an SDP Service, Attribute, or ServiceAttribute search based on information stored in a human readable file.
標簽： Recognizing difficulty SDP generator
上傳時間： 2015-04-16
上傳用戶：dyctj
C-smile OOL is a scripting language with C++-like grammar. It has compiler, VM RUNning bytecodes and C++ extendible RUNtime. Intended to RUN in standlone and embedded mode C-smile 面向對象語言在語法上比較像C＋＋的腳本化的語言，它有一個編譯器，一個運行字節碼的虛擬機，和可擴展的C＋＋運行時。它是為運行獨立的可插入的模塊。
標簽： bytecodes scripting compiler language
上傳時間： 2015-04-29
上傳用戶：asddsd
簡介：PL0語言是pascal語言的一個子集。編譯VC工程之前，需要運行RUN.bat將詞法分析腳本和語法語義分析腳本編譯成C語言。
上傳時間： 2015-05-01
上傳用戶：gengxiaochao
This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 and PORT3.1 This ARM Example may be debugged using only the uVision Simulator and your PC--no additional hardware or evaluation boards are required. The Simulator provides cycle-accurate simulation of all on-chip peripherals of the ADuC7000 device series. You may create various input signals like digital pulses, sine waves, sawtooth waves, and square waves using signal functions which you write in C. Signal functions RUN in the background in the simulator within timing constraints you configure. In this example, several signal functions are defined in the included Startup_SIM.INI file.
標簽： the Analyzer Compiler project
上傳時間： 2013-12-19
上傳用戶：Yukiseop
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To RUN this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) RUN the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program RUNs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
標簽： microcontroll Converter configure following
上傳時間： 2014-12-01
上傳用戶：獨孤求源
The project KEIL_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the Keil ARM toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler RUN-time library which is tuned for single chip systems.
標簽： KEIL_IODemo allocation routines project
上傳時間： 2013-12-08
上傳用戶：ve3344
UART I/O and Memory Allocation Example for GNU The project GNU_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the GNU toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler RUN-time library which is tuned for single chip systems.
標簽： Allocation GNU_IODemo Example project
上傳時間： 2015-05-04
上傳用戶：Amygdala
This companion disc contains the source code for the sample programs presented in INSIDE VISUAL C++ 5.0, as well as pre- compiled copies of the programs. To copy all of the sample code onto your hard disk, RUN the SETUP.EXE program and follow the instructions that appear on the screen. The sample code requires about 10 MB of hard disk space.
標簽： companion the presented contains
上傳時間： 2015-05-09
上傳用戶：mhp0114
這用java語言模擬一個銀行的操作系統，main-class:RUN 圖形界面模式：加參數-graphic 文字模式：加參數-text Client.txt存放客戶信息 Compte.txt存放賬戶信息 Operation.txt賬號使用信息 這個版本是法語版的
上傳時間： 2015-05-09
上傳用戶：hzy5825468
