介紹了電力操作電源與智能電池巡檢系統的特點，給出了一種基于超低功耗單片機MSP430 F149針對中小型變電站自動化運行的專用設備的基本設計原理及實現方法，最后給出了詳細硬件構成和軟件實現。該系統能滿足中小型變電站安全、可靠、自動運行的要求，并通過與上位機的串行通信實現變電站的遠程管理和控制。
Abstract:
The characters of the intelligent battery data logging system of the electric operation power are introduced.The basic design principle and the implemented methods of the special equipment which only designed for the middle or small transformer substation based on MSP430F149 are prescribed. Finally, the hardware block diagram and the software flow chart are also given. The function that the system finally needs to Realize can basically meet with the middle or small transformer substation’s satisfy, reliably,and automatic running.And it can also Realize the transformer substation long-distance management and control by serial communicating with the host computer.
利用Atmel公司的ATmega168微處理器，采用A/D轉換方式來實現按摩椅控制器的鍵盤接口，通過在硬件電路中巧妙地選擇電阻，在軟件設計中采用數字濾波、二分法和區間鑒定等方法，靈敏可靠地實現了按摩椅中30個按鍵的處理。給出了硬件電路設計和軟件設計思想以及部分匯編代碼。
Abstract:
This paper chooses A/D conversion method to Realize the keyboard interface of the controller by using ATmega168 microchip from Atmel Company.It accomplishes 30-key dealing sensitively and reliably in massage chair through skillfully selecting resistors in hardware circuit and using digital filter,dichotomy and area-judging method in software design.The hardware design circuit, software design idea and partly assembles code are presented mainly.
在需要實時大量輸入漢字的顯示控制處理應用中，利用傳統單片機實現顯示控制的設計方法是較難實現的。帶漢字字庫的液晶模塊的使用使得小容量ROM單片機的大量漢字信息輸入與顯示成為可能。提出了針對漢字字庫編碼的二級索引拼音輸入檢索方法,介紹了以ST7920作為控制器的帶漢字字庫的液晶顯示模塊的接口方法及漢字顯示和控制原理，給出了通用計算機鍵盤在單片機中的串行接口，采用該技術可大大增強單片機的漢字輸入功能。為小容量ROM單片機的大批量漢字信息處理提供了一種漢字輸入解決方案。
Abstract:
It is difficult to Realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
基于單DSP的VoIP模擬電話適配器研究與實現:提出和實現了一種新穎的基于單個通用數字信號處理器(DSP)的VoIP模擬電話適配器方案。DSP的I/O和存儲資源非常有限，通常適于運算密集型應用，不適宜控制密集型應用[5]。該系統高效利用單DSP的I/O和片內外存儲器資源，采用μC/OS-II嵌入式實時操作系統，支持SIP和TCP-UDP/IP協議，通過LAN或者寬帶接入，使普通電話機成為Internet終端，實現IP電話。該系統軟硬件結構緊湊高效，運行穩定，成本低，具有廣闊的應用前景。關鍵詞：模擬電話適配器；IP電話；數字信號處理器；μC/OS-II
【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitfixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the analog telephone to Internet and Realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II
Research and Implementation of VoIPATA Based on Single DSP
基于單片機的步進電機開環控制系統:通過ATMEL89C51單片機對步進電機進行控制,主要介紹了步進電機控制器、驅動電路和LED顯示電路的設計,實現了步進電機的開環控制。在步進電機控制器的設計中,重點闡述了脈沖產生電路以及對速度的控制。該系統具有成本低、控制方便的特點。關鍵詞: 單片機; 步進電機; 開環控制
Abstract: The design using ATMEL89C51 single chip to control the step2motor with its controller, driving circuit and LED disp lay circuit to Realize step motor open2loop controlwere introduced. For the controller in this design,the circuit to p roduce pulse and the speed controlwere expatiated emphatically. This system possesses features of lower cost, easier control.Key words: single ch ip; step2motor; open2loop con trol
為了擴大監控范圍，提高資源利用率，降低系統成本，提出了一種多通道視頻切換的解決方案。首先從視頻信號分離出行場信號，然后根據行場信號由DSP和FPGA產生控制信號，控制多路視頻通道之間的切換，從而實現讓一個視頻處理器同時監控不同場景。實驗結果表明，該方案可以在視頻監控告警系統中穩定、可靠地實現視頻通道的切換。
Abstract:
To expand the scope of monitoring， improve resource utilization， reduce system cost， a multiple video channels signal switching method is pointed out in this paper. First， horizontal sync signal and field sync signal from the video signal are separated， then control signal according to the sync signal by DSP and FPGA is generated to control the switching between multiple video channels. Thus， it achieves to make a video processor to monitor different place. Experimental results show that the method can Realize video channel switching reliably， and is applied in the video monitoring warning system successfully.
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。
Abstract:
To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to Realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to Realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully Realize the core function of the STEL-2000A.
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。
Abstract:
In order to Realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。
Abstract:
To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to Realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to Realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully Realize the core function of the STEL-2000A.
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。
Abstract:
In order to Realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
