I. Introduction
This code exploits a previously undisclosed vulnerability in the bit string
decoding code in the Microsoft ASN.1 library. This vulnerability is not related
to the bit string vulnerability described in eEye advisory AD20040210-2. Both
vulnerabilities were fixed in the MS04-007 patch.
II. Screenshots
$ ./kill-bill.pl
. kill-bill : Microsoft ASN.1 remote exploit for CAN-2003-0818 (MS04-007)
by Solar Eclipse <solareclipse@phreedom.org>
Usage: kill-bill -p <port> -s <service> host
Services:
iis IIS HTTP server (port 80)
iis-ssl IIS HTTP server with SSL (port 443)
exchange Microsoft Exchange SMTP server (port 25)
smb-nbt SMB over NetBIOS (port 139)
smb SMB (port 445)
If a service is Running on its default port you don t have to
specify both the service and the port.
Examples: kill-bill -s iis 192.168.0.1
kill-bill -p 80 192.168.0.1
kill-bill -p 1234 -s smb 192.168.0.1
This package contains example software and associated documentation for the
ColdFire MCF5249 microprocessor. The software includes sample processor
initialization routines for the MCF5249 Running a M5249C3 evaluation board as
well as the following sample applications:
simple - empty application template
fat - factory acceptance test for the M5249C3
The software has currently been built and tested under Metrowerks CodeWarrior
加密算法
Test Driver for Crypto++, a C++ Class Library of Cryptographic Primitives:
- To generate an RSA key
cryptest g
- To encrypt and decrypt a string using RSA
cryptest r
- To calculate MD5, SHS, and RIPEMD-160 message digests:
cryptest m file
- To encrypt and decrypt a string using DES-EDE in CBC mode:
cryptest t
- To encrypt or decrypt a file
cryptest e|d input output
- To share a file into shadows:
cryptest s <pieces> <pieces-needed> file
(make sure file has no extension, if you re Running this under DOS)
- To reconstruct a file from shadows:
cryptest j output file1 file2 [....]
- To gzip a file:
cryptest z <compression-level> input output
- To gunzip a file:
cryptest u input output
- To run validation tests:
cryptest v
- To run benchmarks:
cryptest b [time for each benchmark in seconds]
his project was built and tested with WinAVR-20060125.
Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!!
To build the code, just install WinAVR and run "make" from the console in echomaster and
echoslave subdirs.
"make program" will program the device if you have a AVRISP attached.
Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock
from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST!
Otherwise you wont get any clock signal to the AVR and then you can t program it or reset
the fuses!
The MC1319x has default clock output of 32kHz so you will have to set your programmer to
a very low frequency (<=32kHz/4) to be able to program it while it is Running on that!
驅動開發向導
I came across an article QuickSYS which implements an NT driver framework. That article demonstrates a MFC application that gets a project name as a parameter and creates Visual C++ workspace with NT driver framework. I decided to copy the NT driver framework source and to put it in the Visual Studio project wizard as seen above. This is simpler rather than Running an external executable application that generates the code for you.
KVM (for Kernel-based Virtual Machine) is a full virtualization solution for Linux on x86 hardware. It consists of a loadable kernel module (kvm.ko) and a userspace component.
Using KVM, one can run multiple virtual machines Running unmodified Linux or Windows images. Each virtual machine has private virtualized hardware: a network card, disk, graphics adapter, etc.
The kernel component of KVM is included in mainline Linux, and will appear in Linux 2.6.20.
KVM is open source software.
PCI Hot-Plug Specification Revision 1.0
The primary objective of this specification is to enable higher availability of file and application servers by standardizing key aspects of the process of removing and installing PCI adapter cards while the system is Running. Although these same principles can be applied to desktop and portable systems using PCI buses, the operations described here target server platforms.
This document describes the uIP TCP/IP stack. The uIP TCP/IP stack is an extremely small implementation of the TCP/IP protocol suite intended for embedded systems Running low-end 8 or 16-bit microcon-trollers. The code size and RAM requirements of uIP is an order of magnitude smaller than other generic TCP/IP stacks today.
This book describes the following communications applications: Mail, Message Handler( MH), Transmission ControlProtocol/ Internet Protocol(TCP/ IP), Basic Networking Utilities( BNU), and Asynchronous Terminal Emulation( ATE). It provides overviews, concepts, and procedures on receiving and sending mail and messages, transferring files( ftp command), printing files from and to a remote system, Running commands on other systems, communicating between local and remote systems, and customizing the communications environment.
