一種實用的微機自動配料秤系統:介紹一種由單片機構成的配料秤。敘述了秤的傳感器、變送器、信號的變換、硬件原理、軟件流程以及和DCS 系統構成的單回路調節系統,此系統可廣泛地應用于各行業的配料控制中。關鍵詞:配料秤 單片機 單回路調節系統 DCS 系統 Abstract :A proportioning weigher based on single chip computer is introduced. Sensors , transmitters , signal converting , principle of hardware ,software flowchart of proportioning weigher and single loop control system composed with DCS system are emphasized ,this system can be used in proportioning control of various trades extensively.Key Words :Proportioning Weigher ,Single Chip Computer ,Single Loop Control System ,Distributed Control System
上傳時間： 2013-10-12
上傳用戶：zwei41
In this document, the term Ô60xÕ is used to denote a 32-bit microprocessor from the PowerPC architecture family that conforms to the bus interface of the PowerPC 601ª, PowerPC 603ª, or PowerPC 604 microprocessors. Note that this does not include the PowerPC 602ª microprocessor which has a multiplexed address/data bus. 60x processors implement the PowerPC architecture as it is speciÞed for 32-bit addressing, which provides 32-bit effective (logical) addresses, integer data types of 8, 16, and 32 bits,and ßoating-point data types of 32 and 64 bits (single-precision and double-precision).1.1 Overview The MPC106 provides an integrated high-bandwidth, high-performance, TTL-compatible interface between a 60x processor, a secondary (L2) cache or additional (up to four total) 60x processors, the PCI bus,and main memory. This section provides a block diagram showing the major functional units of the 106 and describes brießy how those units interact.Figure 1 shows the major functional units within the 106. Note that this is a conceptual block diagram intended to show the basic features rather than an attempt to show how these features are physically implemented on the device.
上傳時間： 2013-10-08
上傳用戶：18711024007
The Infineon TriCore provides an Interrupt System with a high safety standard. Thisdocument contains some instructions on how to initiate an Interrupt from an externaldevice. First it will show you how to trigger an Interrupt Service Request by an impulseon Port 0 or Port 1. Then in the second part of the document you can find hints how todebounce impulses to enable the use of a simple switch as input device.Authors: Thomas Bliem, CQ Nguyen / Infineon SMI MD Apps
上傳時間： 2013-11-05
上傳用戶：uuuuuuu
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上傳時間： 2013-11-02
上傳用戶：zw380105939
The XA-S3 is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-chip Microcontrollers. The XA-S3 combines many powerful peripherals on one chip. Therefore, it is suited for general multipurpose high performance embedded control functions.One of the on-chip peripherals is the I2C bus interface. This report describes worked-out driver software (written in C) to program / use the I2C interface of the XA-S3. The driver software, together with a demo program and interface software routines offer the user a quick start in writing a complete I2C - XAS3 system application.
上傳時間： 2013-11-10
上傳用戶：liaofamous
基于單片機的汽車多功能報警系統設計The Design of Automobile Multi-function AlarmingBased on Single Chip Computer劉法治趙明富寧睡達(河 南 科 技 學 院 ，新 鄉 453 00 3)摘要介紹了一種基于單片機控制的汽車多功能報警系統，它能對汽車的潤滑系統油壓、制動系統氣壓、冷卻系統溫度、輪胎欠壓及防盜進行自動檢測，并在發現異常情況時，發出聲光報警。闡述了該報警系統的硬件組成及軟件設計方法。關鍵詞單片機傳感器數模轉換報警Abstract Am ulti-fimctiona utomobilea larnungs ystemb asedo ns inglec hipc omputerco ntorlis in torducedin th isp aper.Th eo ilpr essuero flu bricatesystem, air pressure of braking system, temperature of cooling system, under pressure of tyre and guard against theft， detected automaticaly場thesystem. Audio and visual alarms wil be provided under abnormal conditions廠The hardware composition and software design of the system， described.Keywords Singlec hipc omputer Sensor Digital-t-oanaloguec onversion Alarmin 汽車多功能報苦器硬件系統設計根據 系 統 實際需要和產品性價比，選用ATMEL公司新生產的采用CMOs工藝的低功耗、高性能8位單片機AT89S52作為系統的控制器。AT89S52的片內有8k Bytes LSP Flash閃爍存儲器，可進行100(〕次寫、擦除操作;256Bytes內部數據存儲器(RAM);3 2 根可編程輸N輸出線;2個可編程全雙工串行通道;看門狗(WTD)電路等。系統由傳感器、單片機、模數轉換器、無線信號發射電路、指示燈驅動電路、聲光報警驅動電KD一9563，發出三聲二閃光。并觸發一個高電平，驅動無線信號發射電路。
上傳時間： 2013-11-09
上傳用戶：gxmm
一種基于ST62單片機的稱重顯示控制器A Weighing Display Controller Based on ST62 Single Chip Computer祛 FA(上海時博飛奧控制系統有限公司，上海201100)摘要在介紹了基于ST62單片機的基礎上，詳細描述了稱重顯控制器的硬件設計和軟件設計思路。該控制器結構簡單、操作方便、抗擾能力強等優點;具有較好的推廣應用價值。關鍵詞稱重顯示控制儀ST62單片機硬件設計軟件設計Abstract Ont heb asiso fin torductiono fST 62s inglec hipc omputer,th ed esignc oncrptof h ardwarea nds oftwarefo rw eighingd isplayc ontorleris d escrbed.The controler features simple structure, ease operation, powerful capability of anti-interference, etc.，it is wealth to be promoted into practicalapplicationsKeywords We妙噸display0 引言ST62s inglec hip Hardwared esign Softwaer design備 份 振 蕩器，振蕩器保護電路，上電復位及低壓檢測復稱 重 顯 示控制器是一種具有數字顯示、開關量輸出、定值控制和通信功能的以微機為操作核心的稱重控制裝置。它是電子衡器的重要基礎部件，直接影響電子衡器及電子稱重系統的功能和性能。與合適的傳感器及承重傳力復位系統組合可組成配料秤、料斗秤、定值秤、平臺秤、汽車秤等，廣泛應用于電力、化工、建筑、冶金、交通運輸、食品、軍工等部門，是進行自動稱重配料控制和生產過程自動化必不可少的重要檢測、控制裝置。隨著 稱 重 計量自動化水平的提高，對稱重顯示控制器的要求也越來越高。為實現低漂移、高穩定，本控制器采用低漂移、高增益放大器AD620和高分辨率的A/D轉換器CS5550。為提高穩定性和可靠性，采用集成度高的、抗干擾能力強的ST62單片機。
上傳時間： 2013-10-29
上傳用戶：釣鰲牧馬
單片機系統“PC”失控的軟件措施Software Measure of GettingO uto fC ontrolfo r“PC"in S ingleC hipC omputerS ystem謐 加 春 王 曉 基 雷 小 華(江 西 理 工 大 學機 電 工 程 學 院 ，贛 州 34 10 00)摘要單片機系統在實際工業現場中可能遇到各種干擾和自身的隨機性故障?，F場惡劣的環境有可能使計算機系統發生異常，計算機程序指針“PC”失控就是常見的故障之一，如果發生“PC”失控，將導致CPI工作混亂，釀成嚴重的事故。研究了“PC”失控的原因，并指出軟件抗干擾的幾種方法，有效保證單片機系統的正常工作。關鍵詞單片機“PC”失控抗干擾Abstract Inp racticalin dustrialfi elds,th ereis v ariousin terferencea fectingo perationo fsi nglec hipc omputersy stemsa ndt hec omputersy stems。fac噸random faults飾themselves. It is very common that the severe environment makes the computer systems abnormal. The program counter "PC"gettingo utof co ntorlis on eo fth ec ommonfa ults.If th isoc curs,C PUw ouldb eru nningo utof or deran din torducesse riousan cient.T hec ausesof " PC"geting out of control， studied in this paper and some countermeasures of anti-interference師software are given to ensure single chip computer systemworking properly.Keywords Single。飾computer Porgramc ounter"P C" Anti-interfeernc 在設 計 和 開發單片機系統時，一般難以周全地預計單片機系統在實際工業現場中可能遇到的各種干擾和自身的隨機性故障。因此，除了采取防止和抑制干擾的各項措施外，還應該借助于軟件措施克服某些干擾，系統還應具備迅速自行恢復的能力。本文介紹的應對單片機系統PC失控的軟件措施，設計靈活，節省硬件資源，能保證測控系統長期可靠地運行。MC S- 5 1單片機以其優良的性能價格比大量應用于工業現場測試和控制領域。但是，現場惡劣的環境有可能使計算機系統發生異常，計算機程序指針PC失控就是常見的故障之一，一旦發生PC“走飛”，計算機系統就會出現工作混亂，釀成嚴重的事故。為 了 在 CP 失控時盡量減少由此帶來的不利影響，并盡快使系統恢復正常，需要采取一定的軟件措施和硬件措施。常見的硬件措施有“看門狗”電路。軟件措施設置的前提條件是:①在干擾作用下，微機系統硬件部分不會受到任何損壞，或者損壞部分設置有監測狀態可供查詢;②程序區不會受到干擾侵害。單片機系統的程序和表格以及重要的參數均設置在ROM區，不會因干擾的侵人而改變;③ RAM區中的重要數據不會被破壞，或者雖然被破壞，但是可以重新建立。
上傳時間： 2013-11-02
上傳用戶：bhqrd30
The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
上傳時間： 2013-11-01
上傳用戶：ghostparker
什么是JTAG 到底什么是JTAG呢？ JTAG(Joint Test Action Group)聯合測試行動小組)是一種國際標準測試協議（IEEE 1149.1兼容），主要用于芯片內部測試。現在多數的高級器件都支持JTAG協議，如DSP、FPGA器件等。標準的JTAG接口是4線：TMS、 TCK、TDI、TDO，分別為模式選擇、時鐘、數據輸入和數據輸出線。 JTAG最初是用來對芯片進行測試的，基本原理是在器件內部定義一個TAP（Test Access Port�測試訪問口）通過專用的JTAG測試工具對進行內部節點進行測試。JTAG測試允許多個器件通過JTAG接口串聯在一起，形成一個JTAG鏈，能實現對各個器件分別測試?，F在，JTAG接口還常用于實現ISP（In-System rogrammable�在線編程），對FLASH等器件進行編程。 JTAG編程方式是在線編程，傳統生產流程中先對芯片進行預編程現再裝到板上因此而改變，簡化的流程為先固定器件到電路板上，再用JTAG編程，從而大大加快工程進度。JTAG接口可對PSD芯片內部的所有部件進行編程 JTAG的一些說明 通常所說的JTAG大致分兩類，一類用于測試芯片的電氣特性，檢測芯片是否有問題；一類用于Debug；一般支持JTAG的CPU內都包含了這兩個模塊。 一個含有JTAG Debug接口模塊的CPU，只要時鐘正常，就可以通過JTAG接口訪問CPU的內部寄存器和掛在CPU總線上的設備，如FLASH，RAM，SOC（比如4510B，44Box，AT91M系列）內置模塊的寄存器，象UART，Timers，GPIO等等的寄存器。 上面說的只是JTAG接口所具備的能力，要使用這些功能，還需要軟件的配合，具體實現的功能則由具體的軟件決定。 例如下載程序到RAM功能。了解SOC的都知道，要使用外接的RAM，需要參照SOC DataSheet的寄存器說明，設置RAM的基地址，總線寬度，訪問速度等等。有的SOC則還需要Remap，才能正常工作。運行Firmware時，這些設置由Firmware的初始化程序完成。但如果使用JTAG接口，相關的寄存器可能還處在上電值，甚至時錯誤值，RAM不能正常工作，所以下載必然要失敗。要正常使用，先要想辦法設置RAM。在ADW中，可以在Console窗口通過Let 命令設置，在AXD中可以在Console窗口通過Set命令設置。
上傳時間： 2013-10-23
上傳用戶：aeiouetla
