SINGLE-layer neural networks can be trained using various learning algorithms. The best-known algorithms are the Adaline, Perceptron and Backpropagation algorithms for supervised learning. The first two are specific to SINGLE-layer neural networks while the third can be generalized to multi-layer perceptrons.
標簽： SINGLE-layer algorithms best-known networks
上傳時間： 2015-06-17
上傳用戶：趙云興
backprogation step by step (single layer)
標簽： step backprogation single layer
上傳時間： 2017-05-13
上傳用戶：daguda
另一個AODV 程式，無cross-layer的考慮，完全single layer的方式處理，並可執行於Ns2 上
上傳時間： 2015-09-18
上傳用戶：yzhl1988
以太網物理層接口器件-10/100 Mbps Fast Ethernet Physical Layer TX/FX Single Chip Transceiver
標簽： Transceiver Ethernet Physical Single
上傳時間： 2016-10-13
上傳用戶：jackgao
FPGA-based link layer chip S19202 configuration
標簽： configuration FPGA-based S19202 layer
上傳時間： 2013-08-18
上傳用戶：xsnjzljj
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
標簽： Circuitry Operation Single 1017
上傳時間： 2013-12-20
上傳用戶：Wwill
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for batteryoperation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation mustfunction at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
標簽： Circuitry Operation Single Cell
上傳時間： 2013-10-30
上傳用戶：hz07104032
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上傳時間： 2013-10-24
上傳用戶：s藍莓汁
Persistence Layer s ebook and source code.
標簽： Persistence source Layer ebook
上傳時間： 2015-01-14
上傳用戶：咔樂塢
ngrep strives to provide most of GNU grep s common features, applying them to the network layer. ngrep is a pcap-aware tool that will allow you to specify extended regular or hexadecimal expressions to match against data payloads of packets. It currently recognizes TCP, UDP and ICMP across Ethernet, PPP, SLIP, FDDI, Token Ring and null interfaces, and understands bpf filter logic in the same fashion as more common packet sniffing tools, such as tcpdump and snoop.
標簽： applying features network strives
上傳時間： 2014-01-15
上傳用戶：bcjtao
蟲蟲下載站版權所有 京ICP備2021023401號-1
