This ZIP file contains the support files for programming the Infineon C167CR CAN interface. Refer to Application Note 115a for details of this example code. this is part 2
標簽： programming the interface Infineon
上傳時間： 2014-12-03
上傳用戶：lixinxiang
This example demonstrates how to erase, write, and read the on-chip 640-byte EEPROM Data Memory of the Analog Devices ADuC812, ADuC814, ADuC816, and ADuC824 devivces. This example includes a µ Vision2 Project with a target for each supported device.
標簽： demonstrates example on-chip EEPROM
上傳時間： 2015-05-04
上傳用戶：wl9454
This example project shows how to use the Idle Power-Saving Mode of the 8051Fx.
標簽： Power-Saving the example project
上傳時間： 2015-05-04
上傳用戶：weixiao99
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
標簽： microcontroll Converter configure following
上傳時間： 2014-12-01
上傳用戶：獨孤求源
How to Use Tables With the JTable (in the API reference documentation) class you can display tables of data, optionally allowing the user to edit the data. JTable doesn t contain or cache data it s simply a view of your data. Here s a picture of a typical table displayed within a scroll pane
標簽： documentation the reference display
上傳時間： 2013-12-23
上傳用戶：ayfeixiao
that sets the tool tip text using the boldface code in the snippet
標簽： the boldface snippet using
上傳時間： 2013-12-22
上傳用戶：ANRAN
The code is fairly straightforward, except perhaps for the call to convertColumnIndexToModel. That call is necessary because if the user moves the columns around, the view s index for the column doesn t match the model s index for the column. For example, the user might drag the Vegetarian column (which the model considers to be at index 4) so it s displayed as the first column — at view index 0. Since prepareRenderer gives us the view index, we need to translate the view index to a model index so we can be sure we re dealing with the intended column
標簽： convertColumnIndexToModel straightforward perhaps fairly
上傳時間： 2013-12-10
上傳用戶：it男一枚
Shows how to use all list selection modes, using a list selection listener that s shared between a table and list.
標簽： selection list listener between
上傳時間： 2015-05-04
上傳用戶：jichenxi0730
a3load is 8051 firmware that can be used for uploading or downloading to EZ-USB RAM (internal or external). It implements the vendor specific command bRequest = 0xA3. The address to download/upload to/from is specified in the wValue field of the SETUP packet and the length of the transfer in the wLength field. The actual upload/download data is transferred during the DATA stage of the SETUP transfer. This firmware will function on all EZ-USB chips (EZ-USB, EZ-USB FX, FX2, FX2LP, FX1).
標簽： downloading uploading firmware internal
上傳時間： 2013-12-25
上傳用戶：zhaiye
The project KEIL_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a serial interface with the Keil ARM toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the SERIAL.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
標簽： KEIL_IODemo allocation routines project
上傳時間： 2013-12-08
上傳用戶：ve3344
<rt id="24gsc"></rt>