本系統采用電動機電樞供電回路串接采樣電阻的方式來實現對小型直流有刷電動機的轉速測量。該系統主要由二階低通濾波電路,小信號放大電路、單片機測量顯示電路、開關穩壓電源電路等組成。同時自制電機測速裝置,用高頻磁環作為載體,用線圈繞制磁環,利用電磁感應原理檢測電機運行時的漏磁,將變化的磁場信號轉化為磁環上的感應電流。用信號處理單元電路將微弱電信號轉化為脈沖信號,送由單片機檢測,從而達到準確測量電機的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
標簽： 直流電動機
上傳時間： 2022-03-26
上傳用戶：
實驗教學一直是工科教學中不可或缺的組成部分,對培養學生的動手能力,獨立思考能力,創新思維與發散思維具有重要的作用。針對目前電路教學實驗中電路仿真實驗與實物電路實驗各自獨立,無法統一問題,提出將仿真電路實驗與實物電路實驗有機的結合同步操作,并使用Web發布實現遠程實驗操作。采用Multisim作為電路實驗仿真平臺,NI Eiviss II作為實物電路實驗硬件平臺,運用LabVIEW整合Multisim電路仿真實驗與實物電路實驗,實現仿真與實物實驗有機結合,兩種實驗可同步進行。學生在仿真實驗中先可探索實驗,然后做實物實驗。同時運用LabVIEW開發出實驗過程人機交互操作接口界面,使用過程中效果良好。Experimental teaching has always been an indispensable part of engineering education.And it always plays an important role in cultivating students'practical ability,independent thinking ability,innovative thinking and divergent thinking.But simulation experiment and physical experiment cannot be unified in the circuit teaching experiment at present.In order to solve this problem,this paper proposes to combine organically the simulation circuit experiment with physical circuit experiment,and synchronously operate them.This paper uses the WEB publishing to achieve remote experimental operation.Multisim is used as the circuit simulation platform,and NI Eiviss II is used as the physical circuit hardware platform.Multisim circuit simulation experiment and physical circuit experiment are implemented by LabVIEW to realize the combination of simulation experiment and physical experiment.Students do explore experiments in simulation experiment firstly,and then do physical experiment.And this paper uses LabVIEW to develop the experimental man-machine interface.
上傳時間： 2022-04-05
上傳用戶：
German universities and scientists have repeatedly set the intermational standard in drive technology. Identification and active compensation of natural frequencies in oscillatory mechanics, status controls with monitoring structures incorporating acceleration sensors, adaptive compensation of measurement system deficiencies, self-adjusting detent torque compensation… everything invented with only a single aim in mind: to continue improv-ing the motion control, dynamics, precision and processing speed of your machines. For the industrial applicabability of this technology scientific publications in proceedings and laboratory test rigs are not enough. These features consequenty need to be converted into cost-efficient and easily manageable products. That 's exactly what we have done.So in future, if you should need more than today ' smarket can offer you, now everything isgoing to be alright. With our new high-performance ServoOne drive series you will experi-ence
標簽： servoone
上傳時間： 2022-06-24
上傳用戶：kingwide
陀螺儀硬件自檢：相關方法陀螺儀允許用戶測試機械和電氣部分。自檢的代碼在 InvenSense提供的 MotionApps?軟件里面。如果沒有使用 MotionApps?軟件，請參閱下節(Obtaining the Gyroscope Factory Trim (FT) Value)。當自檢啟動，片上的電子設備就會啟動相應的傳感器。這次啟動會使傳感器的 proofmasses的距離相當于一個預定的科里奧利力（Coriolis force）。傳感器的 Proof masses位移變換的結果將在輸出信號中反映。輸出信號用戶可以在自檢反饋看到。自檢反饋（STR）定于如下：Self Test Response=Gyroscope Output with Self Test Enabled — Gyroscope Output with Self Test Disabled自檢反饋通過反饋與出產的評估比較查找變換用于確定這部分通過還是自檢失敗
上傳時間： 2022-07-23
上傳用戶：xsr1983
