<strike id="sguqe"></strike>
<li id="sguqe"></li> Altera recommends the following system configuration: * Pentium II 400 with 512-MB system memory (faster systems give better software performance) * SVGA monitor * CD-ROM drive * One or more of the following I/O ports: - USB port (if using Windows XP or Windows 2000) for USB-Blaster(TM) or MasterBlaster(TM) communications cables, or APU programming unit - Parallel port for ByteBlasterMV(TM) or ByteBlaster(TM) II download cables - Serial port for MasterBlaster communications cable * TCP/IP networking protocol installed * Windows 2000, Windows NT 4.0 with Service Pack 3 or later, or Windows XP * Internet Explorer 5.0 or later Memory & Disk Space Requirements USB開發
標簽： system configuration recommends following
上傳時間： 2015-03-27
上傳用戶：13188549192
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
標簽： microcontroll Converter configure following
上傳時間： 2014-12-01
上傳用戶：獨孤求源
MSimulator是windows下的arm模擬器，可以模擬出nand flash,serial port,touch LCD,keyboard，等
標簽： MSimulator windows arm 模擬
上傳時間： 2014-01-23
上傳用戶：13517191407
s3c44box 的異步串行通信口介紹，the introduction of the asyhnomus serial port of the s3c44b0x
上傳時間： 2015-10-24
上傳用戶：wlcaption
This a USB core stack for the built-in USB device of LPC214x microcontrollers. It handles the hardware interface and USB enumeration/configuration. Also included are application examples like a USB joystick HID and USB serial port emulation.
標簽： microcontrollers USB the built-in
上傳時間： 2015-11-14
上傳用戶：talenthn
Make and answer phone calls Detect tone and pulse digit from the phone line Capture Caller ID Support blind transfer, single-step transfer/conference, consultation transfer/conference, hold, unhold. Control of the local phone handset, microphone and speaker of the modem Send and receive faxes Play and record on the phone line or sound card Play music in background mode Silence detection VU Meter Wave sound editor that allows your end-users to edit their own sound files. Voice recognition and voice synthesis. Full control over the serial port device ZModem file transfer utility File compression and encryption utility
上傳時間： 2013-11-30
上傳用戶：水中浮云
C8051程序， writes text to the serial port of the 8052，用keil編譯
上傳時間： 2016-04-15
上傳用戶：牛布牛
Freediag contains various drivers (ISO9141, ISO14230, SAEJ1850-VPW, SAEJ1850-PWM) for different adapters that connect the PC serial port to a vehicle. It reads vehicle diagnostic info from vehicle electronic control unit (ecu). The source code is compiled and run in linux environment.
上傳時間： 2013-12-24
上傳用戶：lwwhust
單片機與PC通信實例 功能：從PC機串口端接收13個字節的數據，然后將接收到的數據加上 "Serial Port OK!"的后綴后，發送給PC作為應答
上傳時間： 2016-07-01
上傳用戶：stella2015
Infrared remote decode firmware ,use time measure pulse to decode 1 or 0 this code can decode Nec protocal remote controller and than use uart transfer the data to the pc serial port
標簽： decode Infrared firmware measure
上傳時間： 2013-12-29
上傳用戶：wweqas
