Altera recommends the following system configuration: * Pentium II 400 with 512-MB system memory (faster systems give better software performance) * SVGA monitor * CD-ROM drive * One or more of the following I/O ports: - USB port (if using Windows XP or Windows 2000) for USB-Blaster(TM) or MasterBlaster(TM) communications cables, or APU programming unit - Parallel port for ByteBlasterMV(TM) or ByteBlaster(TM) II download cables - Serial port for MasterBlaster communications cable * TCP/IP networking protocol installed * Windows 2000, Windows NT 4.0 with Service Pack 3 or later, or Windows XP * Internet Explorer 5.0 or later Memory & Disk Space Requirements USB開發
標簽： system configuration recommends following
上傳時間： 2015-03-27
上傳用戶：13188549192
CBC下寫的串口編程，API函數實例 I wish this site had been around when I was trying to figure out how to make Serial communications work in Windows95. I, like many programmers, was hit with the double-whammy of having to learn Windows programming and Win95 Serial comm programming at the same time. I found both tasks confusing at best. It was particularly frustrating because I had, over the years, written so much stuff (including lots of Serial comm software) for the DOS environment and numerous embedded applications. Interrupt driven Serial comm, DMA transfer Serial comm, TSR Serial comm, C, assembler, various processors... you name it, it had written it. Yet, everything I knew seemed upside-down in the message-driven-callback world of Windows.
上傳時間： 2014-06-20
上傳用戶：cccole0605
Bus Hound 5.0 Released by RAINMAN Installation: Simply install and when asked use whatever Serial you want
標簽： Installation Released whatever RAINMAN
上傳時間： 2015-04-21
上傳用戶：
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the Serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
標簽： microcontroll Converter configure following
上傳時間： 2014-12-01
上傳用戶：獨孤求源
The project KEIL_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a Serial interface with the Keil ARM toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the Serial.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
標簽： KEIL_IODemo allocation routines project
上傳時間： 2013-12-08
上傳用戶：ve3344
UART I/O and Memory Allocation Example for GNU The project GNU_IODemo shows how to use memory allocation routines (malloc) and char I/O (printf, scanf) via a Serial interface with the GNU toolchain. The I/O functions are adapted for the Analog Devices ADuC7000 series using the Serial.C module. The example also shows the efficiency of the Keil CA ARM Compiler run-time library which is tuned for single chip systems.
標簽： Allocation GNU_IODemo Example project
上傳時間： 2015-05-04
上傳用戶：Amygdala
GDB Remote Stub Backend for debugging an embedded ARM system via JTAG common hardware debug interface. Communication is done via standard TCP/IP GDB Remote Serial Protocol.
標簽： debugging embedded hardware interfac
上傳時間： 2015-06-22
上傳用戶：咔樂塢
Features • Compatible with MCS-51® Products • 8K Bytes of In-System Programmable (ISP) Flash Memory – Endurance: 1000 Write/Erase Cycles • 4.0V to 5.5V Operating Range • Fully Static Operation: 0 Hz to 33 MHz • Three-level Program Memory Lock • 256 x 8-bit Internal RAM • 32 Programmable I/O Lines • Three 16-bit Timer/Counters • Eight Interrupt Sources • Full Duplex UART Serial Channel • Low-power Idle and Power-down Modes • Interrupt Recovery from Power-down Mode • Watchdog Timer • Dual Data Pointer • Power-off Flag
標簽： 8226 Programmable Compatible In-System
上傳時間： 2015-06-27
上傳用戶：dianxin61
Wavelets have widely been used in many signal and image processing applications. In this paper, a new Serial-parallel architecture for wavelet-based image compression is introduced. It is based on a 4-tap wavelet transform, which is realised using some FIFO memory modules implementing a pixel-level pipeline architecture to compress and decompress images. The real filter calculation over 4 · 4 window blocks is done using a tree of carry save adders to ensure the high speed processing required for many applications. The details of implementing both compressor and decompressor sub-systems are given. The primarily analysis reveals that the proposed architecture, implemented using current VLSI technologies, can process a video stream in real time.
標簽： applications processing Wavelets widely
上傳時間： 2014-01-22
上傳用戶：hongmo
RD1006--I2C與存儲器的IP 代碼及說明文檔，lattice提供，I2C Controller for Serial EEPROMs 源代碼可用，并且包含tb文件
上傳時間： 2014-12-06
上傳用戶：15071087253
