現有基于MAX7219芯片的數碼管驅動電路只適用于小尺寸LED，為擴展其使用范圍，在介紹動態顯示芯片MAX7219功能的基礎上，提出了一個基于該芯片的8位高亮度8英寸數碼管驅動電路。電路保留了MAX7219芯片的功能強大、編程簡單等優點，通過74LS273鎖存器和ULN2803達林頓驅動器，實現了對任意大尺寸數碼管提供較高電壓和電流驅動的靜態顯示，并亮度可調。 Abstract: The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with higher voltage and current was achieved with the help of 74LS273 and ULN2803.
標簽： 7219 MAX LED 數碼顯示
上傳時間： 2013-10-23
上傳用戶：31633073
針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
標簽： 單片機 B超 數字化 鍵盤設計
上傳時間： 2013-10-10
上傳用戶：asdfasdfd
Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上傳時間： 2013-10-20
上傳用戶：Maple
提出了一種以S3C2440A為核心處理器的銀行評價器的設計方案，并結合XILINX公司的XL95144XL型CPLD，輔助S3C2440A，實現該銀行評價器的各部分功能以及系統信號之間的相互協調。該評價器在系統設計上采用液晶屏顯示，代替了以往簡單的數碼管電路的顯示模式，在視覺上給人以全新的享受。同時，評價器增加了新的網絡供電方式，只要將評價器連接上網絡就可以正常工作，方便了客戶的使用。總之，此款銀行評價器采用了嵌入式系統的設計方案，大大豐富了系統功能，實現一個銀行評價器設計的新突破。 Abstract: S3C2440A of SamSung company is the core component of the embedded system. A design of bank assessor based on S3C2440A was provided in this paper. It used XL95144XL combined with S3C2440A to realize all the functions and coordination with system signals. This bank assessor used LCD to display instead of the former simple digital display and provided a new seusuous enjoment. Meanwhile，it provided a new method of network power supply，that the bank assessor could regularly work once it connected to the network，which is convenient for customers to use. In a word，this assessor takes embedded system，enriches the system’s functions and reclizes a new breakout.
標簽： S3C2440A
上傳時間： 2013-11-03
上傳用戶：taa123456
生活中許多目標的高度和水平距離需要進行測量。目前主要的測量方法，仍以傳統的皮尺丈量為主，測量效率不高，有時還很不方便，沒有技術成熟的數字式測高測距產品。以基本的數學方法為理論依據，利用遙控小車做為載體，采用角度傳感器測量角度、霍爾傳感器測量水平距離等，通過單片機LM3S615進行數據計算，實現了對待測目標物體的高度、水平距離等數據的快速、精確和數字式的測量，高度測量精度可達99.06%，水平測量精度則可達98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
上傳時間： 2013-10-30
上傳用戶：jackandlee
為提高溫度測量效率，降低系統的成本，擴展傳輸距離，設計出一種新型溫度采集系統。單片機通過控制具有單總線方式的溫度傳感器DS18B20實現對溫度的測量，同時單片機通過控制具有單總線方式300～450MHz頻率范圍內的MAX7044與MAX7033無線發射與接收芯片實現溫度數據的無線傳輸。與傳統溫度采集系統相比，該系統利用單總線方式連接，采用無線傳輸方式實現遠距離通信，易于系統的集成與擴展。實驗結果表明，該系統結構簡單、方便移植，能夠同時實現多達上百點溫度的測量與500m范圍的傳輸。 Abstract: To improve the temperature measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature measure-ment and the transmission range of500meters.
標簽： 單總線 無線溫度 采集 系統設計
上傳時間： 2013-10-29
上傳用戶：515414293
實時時鐘是微機保護裝置的重要部件，在討論P(yáng)CF8583結構與功能的基礎上，提出采用dsPIC33F系列微處理器與串行I2C時鐘PCF8583的接口設計方案，給出了相應的接口電路與軟件流程。該設計方案結構簡單，可靠性高，開發周期短，具有一定的實用與參考價值。所設計的微機保護裝置已投入現場運行，效果良好。 Abstract: Real-time clock chip is an important part in microcomputer protection device.Based on discussing the structure and function of PCF8583，a new interface scheme which uses dsPIC33F microprocessor and serial clock chip（I2C）PCF8583is proposed.The method of the circuit design and the main software flow are introduced in this paper.The scheme has simple structure，higher reliability and shorter exploitation cycle，so has definite practicality or reference value.The microcomputer protection device has been put into operation with better effects.
標簽： 8583 PCF 串行時鐘 中的應用
上傳時間： 2013-11-18
上傳用戶：Thuan
數字信號處理器dsPIC33F集多通道高精度A/D轉換、多通訊模式、看門狗、CMOS Flash技術等于一體，其內部可完成所有數據操作，實現總線不出芯片技術。將該處理器應用于微機保護裝置，提出基于dsPIC33F微處理器的微機保護裝置的設計方案，給出相應的接口電路與軟件流程。該設計方案結構簡單，性價比及可靠性高，開發周期短，具有一定的實用推廣價值。所研制的微機保護裝置現場運行效果良好。 Abstract: The dsPIC33F microprocessor has a plentiful interior resource which contains multi-channel，high precision A/D converters，multi-communication module，watchdog，CMOS Flash technology，and so on.All data manipulations is accomplished interiorly.What is more，it makes the technology that bus does not go beyond the chip comes into practice.The paper put forwards a design scheme based on dsPIC33F microprocessor.The scheme has the advantages of simple structure，high reliability and shortened exploitation cycle.What is more，it has definite practicality and reference.The microcomputer protection device has been put into operation with excellent effects.
上傳時間： 2013-11-16
上傳用戶：開懷常笑
介紹了當前普通標記機控制系統現狀及其存在缺點，給出氣動標記機及相頻修正PWM模式的工作原理。采用ATmega16單片機和USB轉換RS232接口器件CH341T實現驅動控制系統與PC的實時通訊，標記控制系統可升級到USB接口。采用基于ATmega16的相頻修正PWM替換555振蕩電路產生的PWM，可直接通過軟件調整PWM信號。使用達林頓三極管TIP122替代直流繼電器驅動高頻電磁閥，使得電磁閥驅動電路簡單，成本低廉。該控制系統已成功應用于氣動標記機。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
標簽： ATmega 16 標記 控制系統
上傳時間： 2013-10-18
上傳用戶：1427796291
介紹了一種基于C8051F020單片機的多路壓力測量儀。該測量儀選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量儀能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量儀具有測量精度高，沖擊小等特點。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
標簽： C8051F020 單片機 多路 壓力
上傳時間： 2013-11-16
上傳用戶：yare
蟲蟲下載站版權所有 京ICP備2021023401號-1
