Recent advances in low voltage silicon germaniumand BiCMOS processes have allowed the design andproduction of very high speed amplifi ers. Because theprocesses are low voltage, most of the amplifi er designshave incorporated differential inputs and outputs to regainand maximize total output signal swing. Since many lowvoltageapplications are single-ended, the questions arise,“How can I use a differential I/O amplifi er in a single-endedapplication?” and “What are the implications of suchuse?” This Design Note addresses some of the practicalimplications and demonstrates specifi c single-endedapplications using the 3GHz gain-bandwidth LTC6406differential I/O amplifi er.
上傳時間： 2013-11-23
上傳用戶：rocketrevenge
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having outputs based on a frequency or phase, have an advantage over conventional analogue sensors in that their outputs can be measured directly in digital systems by pulse counting.
上傳時間： 2013-10-08
上傳用戶：wuyuying
Highlights the LTC1062 as a lowpass filter in a phase lock loop. Describes how the loop's bandwidth can be increased and the VCO output jitter reduced when the LTC1062 is the loop filter. Compares it with a passive RC loop filter. Also discussed is the use of LTC1062 as simple bandpass and bandstop filter.
上傳時間： 2013-10-24
上傳用戶：chens000
Application considerations and circuits for the LT1001 and LT1002 single and dual precision amplifiers are illustrated in a number of circuits, including strain gauge signal conditioners, linearized platinum RTD circuits, an ultra precision dead zone circuit for motor servos and other examples.
上傳時間： 2013-10-18
上傳用戶：dreamboy36
分析了調幅信號和載波信號之間的相位差與調制信號的極性的對應關系,得出了相敏檢波電路輸出電壓的極性與調制信號的極性有對應關系的結論。為了驗證相敏檢波電路的這一特性,給出3 個電路方案,分別選用理想元件和實際元件,采用Multisim 對其進行仿真實驗,直觀形象地演示了相敏檢波電路的鑒相特性,是傳統的實際操作實驗所不可比擬的。關鍵詞:相敏檢波;鑒相特性;Multisim;電路仿真 Abstract : The corresponding relation between modulation signal polarity and difference phases of amplitudemodulated signal and the carrier signal ,the polarity of phase2sensitive detecting circuit output voltage and the polarity of modulation signal are correspondent . In order to verify this characteristic ,three elect ric circuit s plans are produced ,idea element s and actual element s are selected respectively. Using Multisim to carry on a simulation experiment ,and then demonst rating the phase detecting characteristic of the phase sensitive circuit vividly and directly. Which is t raditional practical experience cannot be com pared.Keywords :phase sensitive detection ;phase2detecting characteristic ;Multisim;circuit simulation
上傳時間： 2013-11-23
上傳用戶：guanhuihong
This reference design (RD) features a fullyassembled and tested surface-mount printed circuitboard (PCB). The RD board utilizes the MAX48851:2 or 2:1 multiplexer and other ICs to implement acomplete video graphics array (VGA) 8:1multiplexer.VGA input/output connections are provided to easilyinterface the MAX4885 RD board with VGAcompatibledevices. The RD board gives the optionto use a single 5V DC power supply (V+), or this RDboard can be powered from any one of the eight VGA sources.
標簽： multiplexer reference VGA
上傳時間： 2013-11-09
上傳用戶：ANRAN
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上傳時間： 2013-10-27
上傳用戶：落花無痕
本文提出用級聯多電平逆變器取代變壓器多重化結構的STATCOM 拓撲結構，用載波相移正弦脈寬調制技術(Carrier phase-shifted SPWM，以下簡稱CPS-SPWM)取代工頻調制。這種基于CPS-SPWM 級聯多電平逆變器的STATCOM 不僅去掉了多重化變壓器，而且用較低的開關頻率可以獲得較高的等效開關頻率的輸出效果，簡化了濾波；針對電力系統強耦合、非線性的特征，本文提出了將自抗擾控制應用于STATCOM 裝置的控制策略，此控制策略不但可以大大縮短動態過程，改善系統的動態性能，而且具有較強的魯棒性。
上傳時間： 2013-11-20
上傳用戶：maqianfeng
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上傳時間： 2013-10-23
上傳用戶：wushengwu
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
上傳時間： 2013-11-10
上傳用戶：子虛烏有
