<strike id="qs4ak"></strike>
一個matlab time dot main cross-correlation， 解壓后在matlab里運行即可，可計算各種數字信號的延遲，沒有密碼
標簽： cross-correlation matlab main time
上傳時間： 2014-01-02
上傳用戶：wlcaption
Real-Time Digital Signal Processing Implementations and Applications Second Edition。實時數字信號處理，非常好。
標簽： Implementations Applications Processing Real-Time
上傳時間： 2015-07-14
上傳用戶：jjj0202
C++ net time 讀取網洛時間
上傳時間： 2014-01-27
上傳用戶：wang5829
A hybrid Particle Swarm Optimization algorithm for functions in the real space.
標簽： Optimization algorithm functions Particle
上傳時間： 2014-01-12
上傳用戶：zhyiroy
short time speeching signal processing
標簽： processing speeching signal short
上傳時間： 2015-07-19
上傳用戶：Amygdala
Readers can pick up this book and become familiar with C++ in a short time. Stan has taken a very broad and complicated topic and reduced it to the essentials that budding C++ programmers need to know to write real programs. His case study is effective and provides a familiar thread throughout the book.
標簽： familiar Readers become short
上傳時間： 2015-07-20
上傳用戶：thinode
That book tell you how to write code effective and learn it .it s better for your time.
標簽： effective better learn write
上傳時間： 2015-07-23
上傳用戶：himbly
工程計算MATLAB code to calculate the reorthogonalized sine tapers input: N = the length of the time series data to be tapered p = the number of tapers requested I = the gap structure a vector of length N I(t) = 1 if there is data at time t, t=1, ..., N I(t) = 0 if there is a gap at time t output: X = N-by-p vector of the reorthogonalized sine taper
標簽： the reorthogonalized calculate MATLAB
上傳時間： 2013-12-17
上傳用戶：wangyi39
fsmlabs的real time linux的內核，版本rtl-3.2-pre
標簽： fsmlabs linux real time
上傳時間： 2013-12-25
上傳用戶：源弋弋
通用ASK信號解碼接收程序 1. 接收數據位數最多為40(5*8)位. 2. 由定時器對time進行漸增,在TCC中斷程序中加入"INC TIME". 3. 寬脈沖最大允許時間和最小允許時間的計算方式: 脈沖允許時間=TCC 中斷時間(us)*設定數據 4. 在接收到完整的數據后建立rx_data_ok標志. 5. 該子程序由主程序調用. 6. 數據格式:rx_data5.7為最高位,rx_data1.0為最低位. 7. 主程序在收到完整的數據后應清空接收數據緩沖區后,才能調用再次接收.
上傳時間： 2015-08-08
上傳用戶：wsf950131
蟲蟲下載站版權所有 京ICP備2021023401號-1
