本實驗指導我們通過處理器創建一個基本的應用程序。應用程序將 控制Spartan-3E Starter kit上的LEDs。 你將添加一個 OPB BRAM 控制器，和修改OPB BRAM中原有的連接部分插入文本。最后你將會發現系統就像你當初設計的一樣運行。
上傳時間： 2014-01-04
上傳用戶：txfyddz
This is the log generated by artila M501 Starter kit while recovering loader, and u-boot
標簽： recovering generated Starter artila
上傳時間： 2013-12-18
上傳用戶：小寶愛考拉
Header file for initialization of Texas Instruments 320TMSc6713 DSP Starter Kit Extremely useful for people working on DSPs
標簽： initialization Instruments Extremely Starter
上傳時間： 2017-08-12
上傳用戶：hasan2015
Thank you for purchasing the Earthshine Design Arduino Starter Kit. You are now well on your way in your journey into the wonderful world of the Arduino and microcontroller electronics. This book will guide you, step by step, through using the Starter Kit to learn about the Arduino hardware, software and general electronics theory. Through the use of electronic projects we will take you from the level of complete beginner through to having an intermediate set of skills in using the Arduino.
標簽： Arduino Starter Manual Kit
上傳時間： 2020-06-09
上傳用戶：shancjb
在汽車發動機起動時，若發動機起動后起動機不能及時斷電，將會燒毀起動機或損壞飛輪齒環；若變速器不在空檔位置起動，則起動機的瞬間動力將使汽車位移，還可能引起交通事故和人身安全。為此介紹一種利用NXP P89LPC901單片機控制的汽車起動保護控制器，通過檢測汽車起動開關、變速箱檔位、發動機轉速，實現對汽車發動機起動過程檢測和保護。起動保護控制器在發動機起動過程中通過采用逐個關閉打開負載系統，解決汽車發動機過程中因起動電流大而對汽車電源的沖擊影響,延長了電瓶壽命。 Abstract: When the automotive engine is started, the engine start motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong operation or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the Starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上傳時間： 2013-10-15
上傳用戶：mikesering
The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using SW routines implemented in C. The code is focused onthe SAB C513, but will fit to all C500 derivatives.Beyond the low level software drivers a test shell is delivered. This shell allows a quicktest of the software drivers by an emulator or a Starter kit demo board.
上傳時間： 2013-11-24
上傳用戶：363186
Altera ModelSim 6.5仿真入門教程，需要的可自行下載。 平臺 軟件：ModelSim-Altera 6.5e （Quartus II 10.0） Starter Edition 內容 1 設計流程 使用ModelSim仿真的基本流程為： 圖1.1 使用 ModelSim仿真的基本流程 2 開始 2.1 新建工程 打開ModelSim后，其畫面如圖2.1所示。
上傳時間： 2014-12-31
上傳用戶：niumeng16
Altera ModelSim 6.5仿真入門教程，需要的可自行下載。 平臺 軟件：ModelSim-Altera 6.5e （Quartus II 10.0） Starter Edition 內容 1 設計流程 使用ModelSim仿真的基本流程為： 圖1.1 使用 ModelSim仿真的基本流程 2 開始 2.1 新建工程 打開ModelSim后，其畫面如圖2.1所示。
上傳時間： 2013-11-09
上傳用戶：qitiand
This application note describes a method for developing block-oriented I/O device drivers for applications that use the DSP/BIOS real-time kernel and includes examples that run with Code Composer Studio v2.1 on the Texas Instruments TMS320C5402 and TMS320C6711 DSP Starter Kits (DSKs). The device driver model presented here has now been superceded with an updated version that supports not only block oriented devices, but also devices such as UARTs, PCI and USB buses and Multimedia cards. Documentation on the updated driver model as well as example drivers and source code can be found in the Device Driver Developer s Kit product now available for download from the TI Developer s Village.
標簽： block-oriented application developing describes
上傳時間： 2015-07-07
上傳用戶：kelimu
該書籍提供了典型的商業智能任務的端到端指導，主要分數據入庫和多維數據分析兩部分。通過學習可以了解怎樣使用“DB2控制中心”和“數據倉庫中心”創建倉庫數據庫以及運用OLAP Starter Kit 對關系數據進行多維分析。
上傳時間： 2013-12-23
上傳用戶：shawvi
