交流頻率轉換器 特點： 精確度0.05%滿刻度(Accuracy 0.05%F.S.) 多種輸入,輸出選擇 輸入與輸出絕緣耐壓2仟伏特/1分鐘 沖擊電壓測試5仟伏特(1.2x50us) (IEC255-4,ANSI C37.90a/1974) 突波電壓測試2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，穩定性高 2:主要規格 精確度: 0.05% F.S. (23 ±5℃) 輸入負載: <0.2VA 最大過載能力:maximum 2 x rated continuous 輸出反應時間: <250ms (0~90%) 輸出負載能力: <10mA for voltage mode <10V for current mode 輸出漣波: <0.1% F.S. 歸零調整范圍: 0~±5% F.S. 最大值調整范圍: 0~±10% F.S. 溫度系數: 50ppm/℃ (0~50℃) 隔離特性: Input/Output/Power/Case 絕緣抗阻: >100M ohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 行動測試: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV (1.2 x 50us) 突波測試: 2.5KV-0.25ms/1MHz 使用環境條件: -20~60℃(20 to 90% RH non-condensed) 存放環境條件: -30~70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-10-11
上傳用戶：xzt
交流電壓，電流轉換器 特點： 精確度0.25%滿刻度(RMS) 多種輸入,輸出選擇 輸入與輸出絕緣耐壓2仟伏特/1分鐘 沖擊電壓測試5仟伏特(1.2x50us) (IEC255-4,ANSI C37.90a/1974) 突波電壓測試2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，穩定性高 2:主要規格 精確度:0.25%F.S.(RMS) (23 ±5℃) 輸入負載: <0.2VA(voltage) <0.2VA(current) 最大過載能力: Current related input:3 x rated continuous 10 x rated 30 sec. ,25 x rated 3sec. 50 x rated 1sec. Voltage related input:maximum 2x rated continuous 輸出反應時間: <250ms (0~90%) 輸出負載能力: <10mA for voltage mode <10V for current mode 輸出漣波: <0.1% F.S. 歸零調整范圍: 0~±5% F.S. 最大值調整范圍: 0~±10% F.S. 溫度系數: 100ppm/℃ (0~50℃) 隔離特性: Input/Output/Power/Case 絕緣抗阻: >100Mohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 行動測試: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV (1.2 x 50us) 突波測試: 2.5KV-0.25ms/1MHz 使用環境條件: -20~60℃(20 to 90% RH non-condensed) 存放環境條件: -30~70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-09
上傳用戶：非衣2016
電路連接 由于數碼管品種多樣，還有共陰共陽的，下面我們使用一個數碼管段碼生成器（在文章結尾） 去解決不同數碼管的問題： 本例作者利用手頭現有的一位不知品牌的共陽數碼管：型號D5611 A/B，在Eagle 找了一個 類似的型號SA56-11，引腳功能一樣可以直接代換。所以下面電路圖使用SA56-11 做引腳說明。 注意： 1. 將數碼管的a~g 段，分別接到Arduino 的D0~D6 上面。如果你手上的數碼管未知的話，可以通過通電測量它哪個引腳對應哪個字段，然后找出a~g 即可。 2. 分清共陰還是共陽。共陰的話，接220Ω電阻到電源負極；共陽的話，接220Ω電阻到電源+5v。 3. 220Ω電阻視數碼管實際工作亮度與手頭現有原件而定，不一定需要準確。 4. 按下按鈕即停。 源代碼 由于我是按照段碼生成器默認接法接的，所以不用修改段碼生成器了，直接在段碼生成器選擇共陽極，再按“自動”生成數組就搞定。 下面是源代碼，由于偷懶不用寫循環，使用了部分AVR 語句。 PORTD 這個是AVR 的端口輸出控制語句，8 位對應D7~D0，PORTD=00001001 就是D3 和D0 是高電平。 PORTD = a;就是找出相應的段碼輸出到D7~D0。 DDRD 這個是AVR 語句中控制引腳作為輸出/輸入的語句。DDRD = 0xFF;就是D0~D7 全部 作為輸出腳了。 ARDUINO CODECOPY /* Arduino 單數碼管骰子 Ansifa 2011-12-28 */ //定義段碼表，表中十個元素由LED 段碼生成器生成，選擇了共陽極。 inta[10] = {0xC0, 0xF9, 0xA4, 0xB0, 0x99, 0x92, 0x82, 0xF8, 0x80, 0x90}; voidsetup() { DDRD = 0xFF; //AVR 定義PortD 的低七位全部用作輸出使用。即0xFF=B11111111對 應D7~D0 pinMode(12, INPUT); //D12用來做骰子暫停的開關 } voidloop() { for(int i = 0; i < 10; i++) { //將段碼輸出PortD 的低7位，即Arduino 的引腳D0~D6，這樣需要取出PORTD 最高位，即 D7的狀態，與段碼相加，之后再輸出。 PORTD = a[i]; delay(50); //延時50ms while(digitalRead(12)) {} //如果D12引腳高電平，則在此死循環,暫停LED 跑 動 } }
上傳時間： 2013-10-15
上傳用戶：baitouyu
特點： 精確度0.1%滿刻度 可作各式數學演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A|/ 16 BIT類比輸出功能 輸入與輸出絕緣耐壓2仟伏特/1分鐘(input/output/power) 寬范圍交直流兩用電源設計 尺寸小,穩定性高
上傳時間： 2014-12-23
上傳用戶：ydd3625
The MAX5713/MAX5714/MAX5715 4-channel, low-power,8-/10-/12-bit, voltage-output digital-to-analog converters(DACs) include output buffers and an internal referencethat is selectable to be 2.048V, 2.500V, or 4.096V. TheMAX5713/MAX5714/MAX5715 accept a wide supplyvoltage range of 2.7V to 5.5V with extremely low power(3mW) consumption to accommodate most low-voltageapplications. A precision external reference input allowsrail-to-rail operation and presents a 100kI (typ) load toan external reference.
上傳時間： 2013-12-23
上傳用戶：ArmKing88
The MAX17600–MAX17605 devices are high-speedMOSFET drivers capable of sinking /sourcing 4A peakcurrents. The devices have various inverting and noninvertingpart options that provide greater flexibility incontrolling the MOSFET. The devices have internal logiccircuitry that prevents shoot-through during output-statchanges. The logic inputs are protected against voltagespikes up to +14V, regardless of VDD voltage. Propagationdelay time is minimized and matched between the dualchannels. The devices have very fast switching time,combined with short propagation delays (12ns typ),making them ideal for high-frequency circuits. Thedevices operate from a +4V to +14V single powersupply and typically consume 1mA of supply current.The MAX17600/MAX17601 have standard TTLinput logic levels, while the MAX17603 /MAX17604/MAX17605 have CMOS-like high-noise margin (HNM)input logic levels. The MAX17600/MAX17603 are dualinverting input drivers, the MAX17601/MAX17604 aredual noninverting input drivers, and the MAX17602 /MAX17605 devices have one noninverting and oneinverting input. These devices are provided with enablepins (ENA, ENB) for better control of driver operation.
上傳時間： 2013-12-20
上傳用戶：zhangxin
A MEMS microphone IC is unique among Analog Devices, Inc., products in that its input is an acoustic pressure wave. For this reason, some specifications included in the data sheets for these parts may not be familiar, or familiar specifications may be applied in unfamiliar ways. This application note explains the specifica-tions and terms found in MEMS microphone data sheets so that the microphone can be appropriately designed into a system.
上傳時間： 2013-10-31
上傳用戶：masochism
The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCconverter tolerances (27.6V to 36.7V).
上傳時間： 2014-12-23
上傳用戶：781354052
This paper presents a space vector modulation(SVM)-based switching strategy for a three-level neutral point clamped (NPC) converter that is adapted as a STATCOM.
上傳時間： 2013-10-20
上傳用戶：zyt
The LTC®1966 is a true RMS-to-DC converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC converters. The LTC1966 RMS-to-DCconverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
上傳時間： 2013-10-12
上傳用戶：qilin
