Methods for designing a maintenance simulation training system for certain kind of radio are introduced. Fault modeling method is used to establish the fault database. The system sets up some typical failures， follow the prompts trainers can locate the fault source and confirm the type to accomplish corresponding fault maintenance training. A training evaluation means is given to examining and evaluating the training performance. The system intuitively and vividly shows the fault maintenance process， it can not only be used in teaching， but also in daily maintenance training to efficiently improve the maintenance operation level. Graphical programming language LabVIEW is used to develop the system platform.
上傳時間： 2013-11-19
上傳用戶：3294322651
為了滿足現代高速通信中頻率快速轉換的需求，基于坐標旋轉數字計算（CORDIC，Coordinate Rotation Digital Computer）算法完成正交直接數字頻率合成（ODDFS，Orthogonal Direct Digital Frequency Synthesizer）電路設計方案。采用MATLAB和Xilinx System Generator開發工具搭建電路的系統模型，通過現場可編程門陣列（FPGA，Field Programmable Gate Array）完成電路的寄存器傳輸級（RTL，Register Transfer Level）驗證，仿真結果表明電路設計具有很高的有效性和可行性。
上傳時間： 2013-11-09
上傳用戶：hfnishi
This paper presents a space vector modulation(SVM)-based switching strategy for a three-level neutral point clamped (NPC) converter that is adapted as a STATCOM.
上傳時間： 2013-10-20
上傳用戶：zyt
This unique guide to designing digital VLSI circuits takes a top-down approach, reflecting the natureof the design process in industry. Starting with architecture design, the book explains the why andhow of digital design, using the physics that designers need to know, and no more.Covering system and component aspects, design verification, VHDL modelling, clocking, signalintegrity, layout, electricaloverstress, field-programmable logic, economic issues, and more, thescope of the book is singularly comprehensive.
標簽： Integrated Digital Circuit Design
上傳時間： 2013-11-04
上傳用戶：life840315
This publication represents the largest LTC commitmentto an application note to date. No other application noteabsorbed as much effort, took so long or cost so much.This level of activity is justified by our belief that high speedmonolithic amplifiers greatly interest users.
標簽： 高速放大器
上傳時間： 2014-01-07
上傳用戶：wfl_yy
高速數字系統設計下載pdf:High-Speed Digital SystemDesign—A Handbook ofInterconnect Theory and DesignPracticesStephen H. HallGarrett W. HallJames A. McCallA Wiley-Interscience Publication JOHN WILEY & SONS, INC.New York • Chichester • Weinheim • Brisbane • Singapore • TorontoCopyright © 2000 by John Wiley & Sons, Inc.speeddigital systems at the platform level. The book walks the reader through everyrequired concept, from basic transmission line theory to digital timing analysis, high-speedmeasurement techniques, as well as many other topics. In doing so, a unique balancebetween theory and practical applications is achieved that will allow the reader not only tounderstand the nature of the problem, but also provide practical guidance to the solution.The level of theoretical understanding is such that the reader will be equipped to see beyondthe immediate practical application and solve problems not contained within these pages.Much of the information in this book has not been needed in past digital designs but isabsolutely necessary today. Most of the information covered here is not covered in standardcollege curricula, at least not in its focus on digital design, which is arguably one of the mostsignificant industries in electrical engineering.The focus of this book is on the design of robust high-volume, high-speed digital productssuch as computer systems, with particular attention paid to computer busses. However, thetheory presented is applicable to any high-speed digital system. All of the techniquescovered in this book have been applied in industry to actual digital products that have beensuccessfully produced and sold in high volume.Practicing engineers and graduate and undergraduate students who have completed basicelectromagnetic or microwave design classes are equipped to fully comprehend the theorypresented in this book. At a practical level, however, basic circuit theory is all thebackground required to apply the formulas in this book.
上傳時間： 2013-10-26
上傳用戶：縹緲
開關在電路中起接通信號或斷開信號的作用。最常見的可控開關是繼電器，當給驅動繼電器的驅動電路加高電平或低電平時，繼電器就吸合或釋放，其觸點接通或斷開電路。CMOS模擬開關是一種可控開關，它不象繼電器那樣可以用在大電流、高電壓場合，只適于處理幅度不超過其工作電壓、電流較小的模擬或數字信號。 一、常用CMOS模擬開關引腳功能和工作原理 1.四雙向模擬開關CD4066 CD4066 的引腳功能如圖1所示。每個封裝內部有4個獨立的模擬開關，每個模擬開關有輸入、輸出、控制三個端子，其中輸入端和輸出端可互換。當控制端加高電平時，開關導通；當控制端加低電平時開關截止。模擬開關導通時，導通電阻為幾十歐姆；模擬開關截止時，呈現很高的阻抗，可以看成為開路。模擬開關可傳輸數字信號和模擬信號，可傳輸的模擬信號的上限頻率為40MHz。各開關間的串擾很小，典型值為－50dB。
上傳時間： 2013-10-27
上傳用戶：bibirnovis
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上傳時間： 2014-12-23
上傳用戶：han_zh
Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
標簽： Considerations Guidelines and Design
上傳時間： 2013-10-14
上傳用戶：ysystc699
第一步，拿到一塊PCB，首先在紙上記錄好所有元氣件的型號，參數，以及位置，尤其是二極管，三極管的方向，IC缺口的方向。最好用數碼相機拍兩張元氣件位置的照片。 第二步，拆掉所有器件，并且將PAD孔里的錫去掉。用酒精將PCB清洗干凈，然后放入掃描儀內，啟動POHTOSHOP，用彩色方式將絲印面掃入，并打印出來備用。 第三步，用水紗紙將TOP LAYER 和BOTTOM LAYER兩層輕微打磨，打磨到銅膜發亮，放入掃描儀，啟動PHOTOSHOP，用彩色方式將兩層分別掃入。注意，PCB在掃描儀內擺放一定要橫平樹直，否則掃描的圖象就無法使用，掃描儀分辨率請選為600。 需要的朋友請下載哦！
上傳時間： 2013-11-17
上傳用戶：zhuimenghuadie
